Wired works but wireless only loads Google

I am able to access everything normally via wired connection. When using WiFi, the only thing I can access is Google.

I’m not sure where to start and Google isn’t getting me anywhere.

Here is my wireless info:


linux-dfyi:~ # hwinfo --wlan
13: PCI 100.0: 0282 WLAN controller                             
  [Created at pci.378]
  Unique ID: yWPJ.kQy5U_ZUp+C
  Parent ID: z8Q3.SQ434Dh94vE
  SysFS ID: /devices/pci0000:00/0000:00:1c.0/0000:01:00.0
  SysFS BusID: 0000:01:00.0
  Hardware Class: network
  Model: "Intel Centrino Advanced-N 6235 AGN"
  Vendor: pci 0x8086 "Intel Corporation"
  Device: pci 0x088e "Centrino Advanced-N 6235"
  SubVendor: pci 0x8086 "Intel Corporation"
  SubDevice: pci 0x4060 "Centrino Advanced-N 6235 AGN"
  Revision: 0x24
  Driver: "iwlwifi"
  Driver Modules: "iwlwifi"
  Device File: wlp1s0
  Features: WLAN
  Memory Range: 0xf7c00000-0xf7c01fff (rw,non-prefetchable)
  IRQ: 29 (no events)
  HW Address: fe:fb:db:90:37:00
  Permanent HW Address: c4:d9:87:09:0d:71
  Link detected: no
  WLAN channels: 1 2 3 4 5 6 7 8 9 10 11 12 13 36 40 44 48 52 56 60 64 100 104 108 112 116 120 124 128 132 136 140
  WLAN frequencies: 2.412 2.417 2.422 2.427 2.432 2.437 2.442 2.447 2.452 2.457 2.462 2.467 2.472 5.18 5.2 5.22 5.24 5.26 5.28 5.3 5.32 5.5 5.52 5.54 5.56 5.58 5.6 5.62 5.64 5.66 5.68 5.7
  WLAN encryption modes: WEP40 WEP104 TKIP CCMP
  WLAN authentication modes: open sharedkey wpa-psk wpa-eap
  Module Alias: "pci:v00008086d0000088Esv00008086sd00004060bc02sc80i00"
  Driver Info #0:
    Driver Status: iwlwifi is active
    Driver Activation Cmd: "modprobe iwlwifi"
  Config Status: cfg=no, avail=yes, need=no, active=unknown
  Attached to: #9 (PCI bridge)

Tumbleweed Version:


NAME="openSUSE Tumbleweed"
# VERSION="20170729"
ID=opensuse
ID_LIKE="suse"
VERSION_ID="20170729"
PRETTY_NAME="openSUSE Tumbleweed"
ANSI_COLOR="0;32"
CPE_NAME="cpe:/o:opensuse:tumbleweed:20170729"

Any ideas?

When connected via wifi - capture and report back with the output from the following…

ip address
ip route
grep name /etc/resolv.conf

It seems to be working now. I’m not sure what I did but here are the outputs you requested in their respective order:

tanner@linux-dfyi:~> ip address1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host 
       valid_lft forever preferred_lft forever
2: enp2s0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN group default qlen 1000
    link/ether 18:67:b0:c2:73:ce brd ff:ff:ff:ff:ff:ff
3: wlp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
    link/ether c4:d9:87:09:0d:71 brd ff:ff:ff:ff:ff:ff
    inet 192.168.1.15/24 brd 192.168.1.255 scope global dynamic wlp1s0
       valid_lft 85455sec preferred_lft 85455sec
    inet6 2600:6c5d:5a00:6b:71fe:f965:83b3:5d0d/64 scope global temporary dynamic 
       valid_lft 604012sec preferred_lft 85402sec
    inet6 2600:6c5d:5a00:6b:ba4c:df29:5853:cf6/64 scope global mngtmpaddr noprefixroute dynamic 
       valid_lft 1185468sec preferred_lft 604761sec
    inet6 fe80::cae0:7c0c:52d4:7919/64 scope link 
       valid_lft forever preferred_lft forever




tanner@linux-dfyi:~> ip route
default via 192.168.1.1 dev wlp1s0 proto static metric 600 
192.168.1.0/24 dev wlp1s0 proto kernel scope link src 192.168.1.15 metric 600 


tanner@linux-dfyi:~> grep name /etc/resolv.conf
nameserver 192.168.1.1
nameserver fe80::a263:91ff:fe9f:9fea%wlp1s0

Good to read that the connection is working as expected. The requested output was just to get the relevant IP info, and that output was as expected for a working connection. :slight_smile: