Hi Everyone!
I have a strange problem (no doubt a simple fix) with Suse 11.0 fresh install and the network not working.
Here goes.
Issue: After install of Suse 11 Network card was detected, updates were completed.
After reboot network/internet was unavailable.
Ran YAST.
Checked Network there were two entries/cards eth0 configured
eth3? Not configured
(have no idea were this came from)
Unable to remove eth3
Re-configured eth0 (network/internet) worked
Rebooted no network same situation as above.
Can anyone help me with this strange problem?
I have attached the output of ifconfig
and hardware specs
Ifconfig
jeff:/home/jeff
ifconfig lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING
MTU:16436
Metric:1
RX packets:160 errors:0 dropped:0 overruns:0 frame:0
TX packets:160 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:12224 (11.9 Kb) TX bytes:12224 (11.9 Kb)
jeff:/home/jeff
ifconfig eth3 Link encap:Ethernet HWaddr xx:xx:xx:xx:xx:xx
inet6 addr: fe80::200:6cff:fef3:72c/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b)
TX bytes:492 (492.0 b)
Interrupt:252 Base address:0xa000lo
Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128
Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:176 errors:0 dropped:0 overruns:0 frame:0
TX packets:176 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:13560 (13.2 Kb) TX bytes:13560 (13.2 Kb)
Network adapter shortend from hardware list
69: udi = ‘/org/freedesktop/Hal/devices/pci_10de_3ef’
pci.vendor_id = 4318 (0x10de)
linux.hotplug_type = 2 (0x2)
info.subsystem = ‘pci’
pci.subsys_product_id = 1007 (0x3ef)
info.product = ‘MCP61 Ethernet’
linux.subsystem = ‘pci’
info.linux.driver = ‘forcedeth’
pci.subsys_vendor_id = 6217 (0x1849)
info.udi = ‘/org/freedesktop/Hal/devices/pci_10de_3ef’
pci.device_class = 6 (0x6)
pci.device_subclass = 128 (0x80)
pci.device_protocol = 0 (0x0)
pci.vendor = ‘nVidia Corporation’
linux.sysfs_path = ‘/sys/devices/pci0000:00/0000:00:07.0’
info.vendor = ‘nVidia Corporation’
info.parent = ‘/org/freedesktop/Hal/devices/computer’
pci.product = ‘MCP61 Ethernet’
pci.linux.sysfs_path = ‘/sys/devices/pci0000:00/0000:00:07.0’
pci.subsys_vendor = ‘ASRock Incorporation’
pci.product_id = 1007 (0x3ef)
pci.subsys_product = ‘939NF6G-VSTA Board’
Thanks for all the great help!
