Suse 11.1 hanging frequently

English Install/Boot/Login
#1

Hi all’
I’m using opensuse 11.1,syetm specification is following
CPU :pentium 4 2.93GHz
motherboard:asus
Hardisk:40 gb maxtor
Ram:1 GB
my system getting hang periodically after some time and the kernal showing the following error message

Mar 9 11:23:25 maxserver kernel: EXT3-fs error (device sda3): ext3_free_blocks_sb: bit already cleared for block 5311012
Mar 9 11:23:25 maxserver kernel: EXT3-fs error (device sda3): ext3_free_blocks_sb: bit already cleared for block 5311033
Mar 9 11:23:37 maxserver kernel: EXT3-fs error (device sda3): ext3_free_blocks_sb: bit already cleared for block 5311302
Mar 9 11:23:37 maxserver kernel: EXT3-fs error (device sda3): ext3_free_blocks_sb: bit already cleared for block 5311305
Mar 9 11:23:37 maxserver kernel: EXT3-fs error (device sda3): ext3_free_blocks_sb: bit already cleared for block 5311310
Mar 9 11:23:37 maxserver kernel: EXT3-fs error (device sda3): ext3_free_blocks_sb: bit already cleared for block 5311340
Mar 9 11:23:37 maxserver kernel: EXT3-fs error (device sda3): ext3_free_blocks_sb: bit already cleared for block 5311684
Mar 9 11:23:37 maxserver kernel: EXT3-fs error (device sda3): ext3_free_blocks_sb: bit already cleared for block 5311693
Mar 9 11:23:37 maxserver kernel: EXT3-fs error (device sda3): ext3_free_blocks_sb: bit already cleared for block 5311703
Mar 9 11:23:37 maxserver kernel: EXT3-fs error (device sda3): ext3_free_blocks_sb: bit already cleared for block 5311715
Mar 9 11:23:37 maxserver kernel: EXT3-fs error (device sda3): ext3_free_blocks_sb: bit already cleared for block 5278015
Mar 9 11:23:41 maxserver kernel: ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
Mar 9 11:23:41 maxserver kernel: ata1.00: BMDMA stat 0x25
Mar 9 11:23:41 maxserver kernel: ata1.00: cmd c8/00:20:ef:44:57/00:00:00:00:00/e1 tag 0 dma 16384 in
Mar 9 11:23:41 maxserver kernel: res 7f/7f:7f:7f:7f:7f/00:00:00:00:00/7f Emask 0x2 (HSM violation)
Mar 9 11:23:41 maxserver kernel: ata1.00: status: { DRDY DF DRQ ERR }
Mar 9 11:23:41 maxserver kernel: ata1.00: error: { UNC IDNF ABRT }
Mar 9 11:23:51 maxserver kernel: ata1.00: revalidation failed (errno=-2)
Mar 9 11:24:15 maxserver kernel: EXT3-fs error (device sda3): ext3_free_blocks_sb: bit already cleared for block 5310898
Mar 9 17:07:02 maxserver SuSEfirewall2: SuSEfirewall2 not active
Mar 9 17:07:17 maxserver rpcbind: cannot create socket for udp6
Mar 9 17:07:17 maxserver rpcbind: cannot create socket for tcp6
Mar 9 17:07:18 maxserver gdm-session-worker[2512]: PAM pam_putenv: NULL pam handle passed
Mar 9 17:07:37 maxserver pulseaudio[3204]: main.c: High-priority scheduling enabled in configuration but not allowed by policy.
Mar 9 17:07:37 maxserver pulseaudio[3204]: core-util.c: setpriority(): Permission denied
Mar 9 17:07:37 maxserver pulseaudio[3204]: ltdl-bind-now.c: Failed to find original dlopen loader.
Mar 9 17:07:38 maxserver pulseaudio[3206]: pid.c: Stale PID file, overwriting.
Mar 9 17:07:46 maxserver gnome-session[2521]: WARNING: Application ‘libcanberra-login-sound.desktop’ failed to register before timeout
Mar 9 17:07:48 maxserver pulseaudio[3447]: pid.c: Daemon already running.
Mar 9 17:07:53 maxserver kernel: hda-intel: IRQ timing workaround is activated for card #0. Suggest a bigger bdl_pos_adj.
Mar 9 17:07:56 maxserver bluetoothd[3500]: Failed to find Bluetooth netlink family
Mar 9 17:07:57 maxserver bluetoothd[3500]: Parsing /etc/bluetooth/network.conf failed: No such file or directory
Mar 9 17:08:00 maxserver kernel: pan0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
Mar 9 17:08:00 maxserver bluetoothd[3500]: Parsing /etc/bluetooth/input.conf failed: No such file or directory
Mar 9 17:08:01 maxserver ifup: No configuration found for pan0
Mar 9 17:08:02 maxserver bluetoothd[3500]: Parsing /etc/bluetooth/audio.conf failed: No such file or directory
Mar 9 17:13:07 maxserver sshd[4072]: error: PAM: Authentication failure for root from localhost
Mar 9 17:13:12 maxserver sshd[4072]: error: PAM: Authentication failure for root from localhost
Mar 9 17:40:47 maxserver kernel: ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
Mar 9 17:40:47 maxserver kernel: ata1.00: cmd c8/00:08:df:32:4c/00:00:00:00:00/e0 tag 0 dma 4096 in
Mar 9 17:40:47 maxserver kernel: res 40/00:00:01:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
Mar 9 17:40:47 maxserver kernel: ata1.00: status: { DRDY }
Mar 9 17:55:58 maxserver console-kit-daemon[1763]: GLib-GObject-WARNING: IA__g_object_get_valist: value location for gchararray' passed as NULL Mar 9 17:56:01 maxserver bonobo-activation-server (max1-5583): could not associate with desktop session: Failed to connect to socket /tmp/dbus-miXgJfZHMO: Connection refused Mar 9 17:56:03 maxserver auditd[2463]: Error sending signal_info request (Operation not supported) Mar 9 17:56:07 maxserver rpcbind: rpcbind terminating on signal. Restart with "rpcbind -w" Mar 9 17:57:32 maxserver SuSEfirewall2: SuSEfirewall2 not active Mar 9 17:57:33 maxserver rpcbind: cannot create socket for udp6 Mar 9 17:57:33 maxserver rpcbind: cannot create socket for tcp6 Mar 9 17:57:33 maxserver kernel: [drm:i915_getparam] *ERROR* Unknown parameter 5 Mar 9 17:57:34 maxserver kernel: [drm:i915_getparam] *ERROR* Unknown parameter 5 Mar 9 17:57:36 maxserver gdm-session-worker[2627]: PAM pam_putenv: NULL pam handle passed Mar 9 17:57:50 maxserver pulseaudio[3142]: main.c: High-priority scheduling enabled in configuration but not allowed by policy. Mar 9 17:57:50 maxserver pulseaudio[3142]: core-util.c: setpriority(): Permission denied Mar 9 17:57:50 maxserver pulseaudio[3142]: ltdl-bind-now.c: Failed to find original dlopen loader. Mar 9 17:57:50 maxserver pulseaudio[3168]: pid.c: Stale PID file, overwriting. Mar 9 17:57:58 maxserver gnome-session[2642]: WARNING: Application 'libcanberra-login-sound.desktop' failed to register before timeout Mar 9 17:58:00 maxserver pulseaudio[3322]: pid.c: Daemon already running. Mar 9 17:58:08 maxserver bluetoothd[3421]: Failed to find Bluetooth netlink family Mar 9 17:58:08 maxserver bluetoothd[3421]: Parsing /etc/bluetooth/network.conf failed: No such file or directory Mar 9 17:58:08 maxserver kernel: pan0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature. Mar 9 17:58:08 maxserver bluetoothd[3421]: Parsing /etc/bluetooth/input.conf failed: No such file or directory Mar 9 17:58:08 maxserver bluetoothd[3421]: Parsing /etc/bluetooth/audio.conf failed: No such file or directory Mar 9 17:58:09 maxserver ifup: No configuration found for pan0 Mar 9 17:58:51 maxserver console-kit-daemon[1904]: GLib-GObject-WARNING: IA__g_object_get_valist: value location for gchararray’ passed as NULL
Mar 9 17:58:59 maxserver auditd[3196]: Error sending signal_info request (Operation not supported)
Mar 9 17:59:01 maxserver rpcbind: rpcbind terminating on signal. Restart with “rpcbind -w”
Mar 9 18:00:15 maxserver SuSEfirewall2: SuSEfirewall2 not active
Mar 9 18:00:16 maxserver rpcbind: cannot create socket for udp6
Mar 9 18:00:16 maxserver rpcbind: cannot create socket for tcp6
Mar 9 18:00:17 maxserver kernel: [drm:i915_getparam] ERROR Unknown parameter 5
Mar 9 18:00:18 maxserver kernel: [drm:i915_getparam] ERROR Unknown parameter 5
Mar 9 18:00:19 maxserver gdm-session-worker[2530]: PAM pam_putenv: NULL pam handle passed
Mar 9 18:00:34 maxserver pulseaudio[3077]: main.c: High-priority scheduling enabled in configuration but not allowed by policy.
Mar 9 18:00:34 maxserver pulseaudio[3077]: core-util.c: setpriority(): Permission denied
Mar 9 18:00:34 maxserver pulseaudio[3077]: ltdl-bind-now.c: Failed to find original dlopen loader.
Mar 9 18:00:35 maxserver pulseaudio[3099]: pid.c: Stale PID file, overwriting.
Mar 9 18:00:43 maxserver gnome-session[2545]: WARNING: Application ‘libcanberra-login-sound.desktop’ failed to register before timeout
Mar 9 18:00:46 maxserver pulseaudio[3286]: pid.c: Daemon already running.
Mar 9 18:00:47 maxserver bluetoothd[3288]: Failed to find Bluetooth netlink family
Mar 9 18:00:47 maxserver bluetoothd[3288]: Parsing /etc/bluetooth/network.conf failed: No such file or directory
Mar 9 18:00:49 maxserver kernel: pan0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
Mar 9 18:00:49 maxserver ifup: No configuration found for pan0
Mar 9 18:00:51 maxserver bluetoothd[3288]: Parsing /etc/bluetooth/input.conf failed: No such file or directory
Mar 9 18:00:52 maxserver bluetoothd[3288]: Parsing /etc/bluetooth/audio.conf failed: No such file or directory

Mar 9 20:01:22 maxserver rpcbind: rpcbind terminating on signal. Restart with “rpcbind -w”
Mar 9 20:16:30 maxserver SuSEfirewall2: SuSEfirewall2 not active
Mar 9 20:16:32 maxserver rpcbind: cannot create socket for udp6
Mar 9 20:16:32 maxserver rpcbind: cannot create socket for tcp6
Mar 9 20:16:33 maxserver kernel: [drm:i915_getparam] ERROR Unknown parameter 5
Mar 9 20:16:34 maxserver kernel: [drm:i915_getparam] ERROR Unknown parameter 5
Mar 9 20:16:35 maxserver gdm-session-worker[2617]: PAM pam_putenv: NULL pam handle passed
Mar 9 20:16:54 maxserver pulseaudio[3255]: main.c: High-priority scheduling enabled in configuration but not allowed by policy.
Mar 9 20:16:54 maxserver pulseaudio[3255]: core-util.c: setpriority(): Permission denied
Mar 9 20:16:54 maxserver pulseaudio[3255]: ltdl-bind-now.c: Failed to find original dlopen loader.
Mar 9 20:16:54 maxserver pulseaudio[3259]: pid.c: Stale PID file, overwriting.
Mar 9 20:17:03 maxserver gnome-session[2632]: WARNING: Application ‘libcanberra-login-sound.desktop’ failed to register before timeout
Mar 9 20:17:04 maxserver pulseaudio[3399]: pid.c: Daemon already running.
Mar 9 20:17:07 maxserver bluetoothd[3431]: Failed to find Bluetooth netlink family
Mar 9 20:17:09 maxserver bluetoothd[3431]: Parsing /etc/bluetooth/network.conf failed: No such file or directory
Mar 9 20:17:12 maxserver kernel: pan0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
Mar 9 20:17:12 maxserver bluetoothd[3431]: Parsing /etc/bluetooth/input.conf failed: No such file or directory
Mar 9 20:17:12 maxserver bluetoothd[3431]: Parsing /etc/bluetooth/audio.conf failed: No such file or directory
Mar 9 20:17:13 maxserver ifup: No configuration found for pan0
Mar 9 20:27:25 maxserver kernel: [drm:i915_getparam] ERROR Unknown parameter 5
Mar 9 20:28:50 maxserver console-kit-daemon[1886]: GLib-GObject-WARNING: IA__g_object_get_valist: value location for `gchararray’ passed as NULL
Mar 9 20:28:54 maxserver auditd[3144]: Error sending signal_info request (Operation not supported)
Mar 9 20:28:57 maxserver rpcbind: rpcbind terminating on signal. Restart with “rpcbind -w”
Mar 10 09:43:55 maxserver SuSEfirewall2: SuSEfirewall2 not active
Mar 10 09:44:00 maxserver rpcbind: cannot create socket for udp6
Mar 10 09:44:00 maxserver rpcbind: cannot create socket for tcp6
Mar 10 09:44:02 maxserver kernel: [drm:i915_getparam] ERROR Unknown parameter 5
Mar 10 09:44:03 maxserver kernel: [drm:i915_getparam] ERROR Unknown parameter 5
Mar 10 09:44:04 maxserver gdm-session-worker[2650]: PAM pam_putenv: NULL pam handle passed
Mar 10 09:44:23 maxserver pulseaudio[3321]: main.c: High-priority scheduling enabled in configuration but not allowed by policy.
Mar 10 09:44:23 maxserver pulseaudio[3321]: core-util.c: setpriority(): Permission denied
Mar 10 09:44:23 maxserver pulseaudio[3321]: ltdl-bind-now.c: Failed to find original dlopen loader.
Mar 10 09:44:23 maxserver pulseaudio[3332]: pid.c: Stale PID file, overwriting.
Mar 10 09:44:32 maxserver gnome-session[2665]: WARNING: Application ‘libcanberra-login-sound.desktop’ failed to register before timeout
Mar 10 09:44:34 maxserver pulseaudio[3425]: pid.c: Daemon already running.
Mar 10 09:44:39 maxserver bluetoothd[3534]: Failed to find Bluetooth netlink family
Mar 10 09:44:39 maxserver bluetoothd[3534]: Parsing /etc/bluetooth/network.conf failed: No such file or directory
Mar 10 09:44:44 maxserver kernel: pan0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
Mar 10 09:44:45 maxserver ifup: No configuration found for pan0
Mar 10 09:44:45 maxserver bluetoothd[3534]: Parsing /etc/bluetooth/input.conf failed: No such file or directory
Mar 10 09:44:45 maxserver bluetoothd[3534]: Parsing /etc/bluetooth/audio.conf failed: No such file or directory
Mar 10 09:52:27 maxserver kernel: ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
Mar 10 09:52:27 maxserver kernel: ata1.00: cmd c8/00:08:22:5c:8f/00:00:00:00:00/e4 tag 0 dma 4096 in
Mar 10 09:52:27 maxserver kernel: res 40/00:00:01:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
Mar 10 09:52:27 maxserver kernel: ata1.00: status: { DRDY }
Mar 10 10:01:31 maxserver kernel: [drm:i915_getparam] ERROR Unknown parameter 5
Mar 10 10:05:42 maxserver kernel: [drm:i915_getparam] ERROR Unknown parameter 5
Mar 10 10:05:55 maxserver kernel: [drm:i915_getparam] ERROR Unknown parameter 5

ata1: clearing spurious IRQ
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.00: cmd ca/00:10:6f:e5:4f/00:00:00:00:00/e1 tag 0 dma 8192 out
res 40/00:00:01:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
ata1: soft resetting link
ata1: clearing spurious IRQ
ata1: clearing spurious IRQ
ata1: clearing spurious IRQ
ata1.00: configured for UDMA/100
ata1: EH complete
sd 0:0:0:0: [sda] 80293248 512-byte hardware sectors: (41.1GB/38.2GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn’t support DPO or FUA

please help me

#2

Is “ata1” in this case a CD/DVD device or a harddisk?

#3

hi Chrysantine,
thank you for your replay.In my case it is a Hard disk.

Regards
Shaiju

#4

It seems the system is having trouble reading/write to it and is thus having issues (and would cause freezes. I would suggest backing up the contents of that hard drive and replacing it - it’s most likely going bad.

#5

hi Chrysantine,
thanks for the rplay
that means Hard Disk issue…can i overcome the issue without changing the hard drive(like formatting the harddrive)…
Does suse support sata hard drives;

I have another suse machine…it showing [drm:i915_getparam] ERROR Unknown parameter 5
.and system is little slow.can u give an advise about that…

Reagrds
Shaiju

#6

Suse supports SATA drives without any problem.

  1. If your drive is damaged there will probably no other way than to change it.

Eventually, if your drive is IDE and you did mount your system from the scratch you could look for the following issues:

  1. If IDE HDD and IDE-CD drives are on the same controller, this can lead to problems. Make sure that (if you are using IDE HDD and IDE DVD/CD drives), that they are using two different IDE controllers.

  2. One possible problem with IDE could also be a not well attached IDE cable and/or a broken IDE cable. Check whether the cable is well plugged (in the HDD and in the controller). If you have a spare cable try to change the cable and see if the problems still presents.

  3. Note that, if your IDE drive is still one with jumper setting, the "cable-select" jumper setting might lead to problems with certain controllers. This is a hardware related problem and will affect any installation. If your IDE HDD is master (what a system disk should be), then set it explicitly as master and not on “cable select”.

  4. in all cases make immediately a backup if you have important data on the PC. In case you do not know how, you may ask in this forum. With Linux it is very easy to copy a whole home directory with few commands on an external HDD.

On you question about the other PC. You need to post the log extract in order to make us understand.
Cheers.

#7

thank you for the replay.I have changed the IDE cable and now looking pretty good…0:00:1d.3
sda1 sda2 sda3
sd 0:0:0:0: [sda] Attached SCSI disk
PM: Starting manual resume from disk
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
udevd version 128 started
sd 0:0:0:0: Attached scsi generic sg0 type 0
intel_rng: FWH not detected
input: PC Speaker as /devices/platform/pcspkr/input/input2
i801_smbus 0000:00:1f.3: PCI INT B → GSI 19 (level, low) → IRQ 19
input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
Linux agpgart interface v0.103
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4
parport_pc 00:08: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
ACPI: Power Button (CM) [PWRB]
iTCO_vendor_support: vendor-support=0
agpgart-intel 0000:00:00.0: Intel 915G Chipset
agpgart-intel 0000:00:00.0: detected 7932K stolen memory
agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
iTCO_wdt: Found a ICH6 or ICH6R TCO device (Version=2, TCOBASE=0x0460)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, hpet irqs
ppdev: user-space parallel port driver
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
vendor=8086 device=244e
r8169 0000:01:02.0: PCI INT A → GSI 17 (level, low) → IRQ 17
r8169 0000:01:02.0: no PCI Express capability
eth0: RTL8110s at 0xf915c000, 00:15:f2:ae:79:d3, XID 04000000 IRQ 17
HDA Intel 0000:00:1b.0: PCI INT A → GSI 16 (level, low) → IRQ 16
HDA Intel 0000:00:1b.0: setting latency timer to 64
Adding 1534168k swap on /dev/sda1. Priority:-1 extents:1 across:1534168k
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
loop: module loaded
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
fuse init (API version 7.9)
type=1505 audit(1268222103.128:2): operation=“profile_load” name="/bin/ping" name2=“default” pid=1653
type=1505 audit(1268222103.176:3): operation=“profile_load” name="/sbin/klogd" name2=“default” pid=1654
type=1505 audit(1268222103.264:4): operation=“profile_load” name="/sbin/syslog-ng" name2=“default” pid=1655
type=1505 audit(1268222103.384:5): operation=“profile_load” name="/sbin/syslogd" name2=“default” pid=1657
type=1505 audit(1268222103.532:6): operation=“profile_load” name="/usr/sbin/avahi-daemon" name2=“default” pid=1670
type=1505 audit(1268222103.684:7): operation=“profile_load” name="/usr/sbin/identd" name2=“default” pid=1694
type=1505 audit(1268222103.792:8): operation=“profile_load” name="/usr/sbin/mdnsd" name2=“default” pid=1721
type=1505 audit(1268222103.988:9): operation=“profile_load” name="/usr/sbin/nscd" name2=“default” pid=1735
type=1505 audit(1268222104.140:10): operation=“profile_load” name="/usr/sbin/ntpd" name2=“default” pid=1753
type=1505 audit(1268222104.220:11): operation=“profile_load” name="/usr/sbin/traceroute" name2=“default” pid=1754
powernow: This module only works with AMD K7 CPUs
r8169: eth0: link up
[drm] Initialized drm 1.1.0 20060810
pci 0000:00:02.0: PCI INT A → GSI 16 (level, low) → IRQ 16
pci 0000:00:02.0: setting latency timer to 64
[drm] Initialized i915 1.6.0 20060119 on minor 0
[drm:i915_getparam] ERROR Unknown parameter 5
[drm:i915_getparam] ERROR Unknown parameter 5
bootsplash: status on console 0 changed to on
Bluetooth: Core ver 2.13
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.11
Bluetooth: L2CAP socket layer initialized
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.10
Bridge firewalling registered
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
parport_pc 00:08: disabled
parport 0x378 (WARNING): CTR: wrote 0x0c, read 0xff
parport 0x378 (WARNING): DATA: wrote 0xaa, read 0xff
parport 0x378: You gave this address, but there is probably no parallel port there!
parport0: PC-style at 0x378 [PCSPP,TRISTATE]
lp0: using parport0 (polling).
parport_pc 00:08: activated
parport_pc 00:08: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
lp0: using parport0 (interrupt-driven).
ppa: Version 2.07 (for Linux 2.4.x)
st: Version 20080504, fixed bufsize 32768, s/g segs 256

The following is the other PC’s Log
EXT3-fs: mounted filesystem with ordered data mode.
udevd version 128 started
sd 2:0:0:0: Attached scsi generic sg0 type 0
input: PC Speaker as /devices/platform/pcspkr/input/input2
Linux agpgart interface v0.103
agpgart-intel 0000:00:00.0: Intel G33 Chipset
agpgart-intel 0000:00:00.0: detected 7164K stolen memory
agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
intel_rng: FWH not detected
input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4
ACPI: Power Button (CM) [PWRB]
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
vendor=8086 device=27d2
r8169 0000:02:00.0: PCI INT A → GSI 17 (level, low) → IRQ 17
r8169 0000:02:00.0: setting latency timer to 64
r8169 0000:02:00.0: unknown MAC (27a00000)
eth0: RTL8169 at 0xf9022000, 00:30:67:22:4c:54, XID 24a00000 IRQ 221
rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, hpet irqs
iTCO_vendor_support: vendor-support=0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0860)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
i801_smbus 0000:00:1f.3: PCI INT B → GSI 19 (level, low) → IRQ 19
HDA Intel 0000:00:1b.0: PCI INT A → GSI 16 (level, low) → IRQ 16
HDA Intel 0000:00:1b.0: setting latency timer to 64
hda_codec: Unknown model for ALC662, trying auto-probe from BIOS…
ALSA sound/pci/hda/hda_codec.c:3047: autoconfig: line_outs=1 (0x14/0x0/0x0/0x0/0x0)
ALSA sound/pci/hda/hda_codec.c:3051: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
ALSA sound/pci/hda/hda_codec.c:3055: hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
ALSA sound/pci/hda/hda_codec.c:3056: mono: mono_out=0x0
ALSA sound/pci/hda/hda_codec.c:3064: inputs: mic=0x18, fmic=0x19, line=0x1a, fline=0x0, cd=0x0, aux=0x0
Adding 2104472k swap on /dev/sda1. Priority:-1 extents:1 across:2104472k
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
loop: module loaded
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
fuse init (API version 7.9)
type=1505 audit(1268195021.260:2): operation=“profile_load” name="/bin/ping" name2=“default” pid=1642
type=1505 audit(1268195021.316:3): operation=“profile_load” name="/sbin/klogd" name2=“default” pid=1678
type=1505 audit(1268195021.404:4): operation=“profile_load” name="/sbin/syslog-ng" name2=“default” pid=1680
type=1505 audit(1268195021.468:5): operation=“profile_load” name="/sbin/syslogd" name2=“default” pid=1681
type=1505 audit(1268195021.528:6): operation=“profile_load” name="/usr/sbin/avahi-daemon" name2=“default” pid=1682
type=1505 audit(1268195021.584:7): operation=“profile_load” name="/usr/sbin/identd" name2=“default” pid=1683
type=1505 audit(1268195021.644:8): operation=“profile_load” name="/usr/sbin/mdnsd" name2=“default” pid=1684
type=1505 audit(1268195021.720:9): operation=“profile_load” name="/usr/sbin/nscd" name2=“default” pid=1685
type=1505 audit(1268195021.804:10): operation=“profile_load” name="/usr/sbin/ntpd" name2=“default” pid=1686
type=1505 audit(1268195021.860:11): operation=“profile_load” name="/usr/sbin/traceroute" name2=“default” pid=1687
powernow: This module only works with AMD K7 CPUs
r8169: eth0: link up
r8169: eth0: link up
[drm] Initialized drm 1.1.0 20060810
pci 0000:00:02.0: PCI INT A → GSI 16 (level, low) → IRQ 16
pci 0000:00:02.0: setting latency timer to 64
[drm] Initialized i915 1.6.0 20060119 on minor 0
[drm:i915_getparam] ERROR Unknown parameter 5
set status page addr 0x00133000
[drm:i915_getparam] ERROR Unknown parameter 5
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
bootsplash: status on console 0 changed to on
eth0: no IPv6 routers present
Bluetooth: Core ver 2.13
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.11
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.10
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bridge firewalling registered
pan0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
[drm:i915_getparam] ERROR Unknown parameter 5
[drm:i915_getparam] ERROR Unknown parameter 5
[drm:i915_getparam] ERROR Unknown parameter 5
[drm:i915_getparam] ERROR Unknown parameter 5
[drm:i915_getparam] ERROR Unknown parameter 5
[drm:i915_getparam] ERROR Unknown parameter 5
[drm:i915_getparam] ERROR Unknown parameter 5
[drm:i915_getparam] ERROR Unknown parameter 5
[drm:i915_getparam] ERROR Unknown parameter 5
[drm:i915_getparam] ERROR Unknown parameter 5
[drm:i915_getparam] ERROR Unknown parameter 5
[drm:i915_getparam] ERROR Unknown parameter 5
[drm:i915_getparam] ERROR Unknown parameter 5
[drm:i915_getparam] ERROR Unknown parameter 5
[drm:i915_getparam] ERROR Unknown parameter 5
[drm:i915_getparam] ERROR Unknown parameter 5
[drm:i915_getparam] ERROR Unknown parameter 5
[drm:i915_getparam] ERROR Unknown parameter 5
[drm:i915_getparam] ERROR Unknown parameter 5
[drm:i915_getparam] ERROR Unknown parameter 5
[drm:i915_getparam] ERROR Unknown parameter 5
[drm:i915_getparam] ERROR Unknown parameter 5
[drm:i915_getparam] ERROR Unknown parameter 5
[drm:i915_getparam] ERROR Unknown parameter 5
[drm:i915_getparam] ERROR Unknown parameter 5
[drm:i915_getparam] ERROR Unknown parameter 5

Regards
shaiju

#8

[drm:i915_getparam] ERROR Unknown parameter 5
is for what I know an intel driver bug. Did you try to update to the lastes available intel video driver?
If you did, and the problem presented afterwards: did you try to downgrade to the official intel video driver?
One of the two solution should be the right for you.

Which opensSuse version is running on that PC?
Regards