Remote VNC funktioniert nicht mit neu installierter OpenSuse 13.1

Deutsch (German) Installation/Administration
#1

Hi,

bei meiner frisch installierten OpenSuse 13.1 kann ich keine Remove VNC Session eröffnen. Beim versuch einer Verbindung kann ich sehen wie der Login Screen aufgebaut wird, allerdings bevor dieser fertig dargestellt ist, wird die Verbindung abgebrochen. Folgendes kann ich in den Logfiles sehen:

/var/log/messages
2013-12-11T10:15:50.274163+01:00 myserver xinetd[803]: START: vnc1 from=10.80.29.1
2013-12-11T10:15:50.539294+01:00 myserver kdm_config[3334]: Multiple occurrences of section [General] in /usr/share/kde4/config/kdm/kdmrc. Consider merging them.
2013-12-11T10:02:54.199642+01:00 myserver sudo: message repeated 19 times: pam_unix(sudo:auth): auth could not identify password for [root]]
2013-12-11T10:15:50.540080+01:00 myserver kdm_config[3334]: Multiple occurrences of section [Xdmcp] in /usr/share/kde4/config/kdm/kdmrc. Consider merging them.
2013-12-11T10:15:50.540448+01:00 myserver kdm_config[3334]: Multiple occurrences of section [X--Core] in /usr/share/kde4/config/kdm/kdmrc. Consider merging them.
2013-12-11T10:15:50.540818+01:00 myserver kdm_config[3334]: Multiple occurrences of section [X--Greeter] in /usr/share/kde4/config/kdm/kdmrc. Consider merging them.
2013-12-11T10:15:50.541208+01:00 myserver kdm_config[3334]: Multiple occurrences of section [X-:*-Core] in /usr/share/kde4/config/kdm/kdmrc. Consider merging them.
2013-12-11T10:15:50.541554+01:00 myserver kdm_config[3334]: Multiple occurrences of section [X-:0-Core] in /usr/share/kde4/config/kdm/kdmrc. Consider merging them.
2013-12-11T10:15:50.541901+01:00 myserver kdm[3805]: plymouth should quit after server startup
2013-12-11T10:15:51.285500+01:00 myserver kdm: localhost:1[3340]: Abnormal termination of greeter for display localhost:1, code 1, signal 0
2013-12-11T10:15:51.296061+01:00 myserver xinetd[803]: EXIT: vnc1 status=0 duration=1(sec)

/var/log/kdm.log
klauncher(3348) kdemain: No DBUS session-bus found. Check if you have started the DBUS server.
kdeinit4: Communication error with launcher. Exiting!
kdmgreet(3341)/kdecore (KTimeZone): KSystemTimeZones: ktimezoned initialize() D-Bus call failed: “Not connected to D-Bus server”

kdmgreet(3341)/kdecore (KTimeZone): No time zone information obtained from ktimezoned
X Error of failed request: BadAccess (attempt to access private resource denied)
Major opcode of failed request: 131 (MIT-SHM)
Minor opcode of failed request: 1 (X_ShmAttach)
Serial number of failed request: 605
Current serial number in output stream: 606

Woran könnte das liegen???

Cheers

#2

I had the same issue.

at a terminal window type
dbus-launch vncserver
enter a password
take note of the session/port # (2, 3, 4, etc)

go to /home/your_username/.vnc (it is a hidden folder)
edit the file xstartup (I would save it first)

for KDE contents should be
#!/bin/sh
/usr/bin/startkde

for GNOME contents should be
#!/bin/sh
/usr/bin/gnome &

had to REBOOT after editing xstartup to get GUI’s to come

from vnc client enter address of server followed by session number
like xxx.xxx.xxx.xxx:# (e.g. 192.168.2.8:2)
enter password when prompted

This will get you started.
read the article at the following link to set up other options like KDE or GNOME interfaces and to setup automatic start on boot

TightVNC (VNC Xvnc) on openSUSE as Client or Server (Remote Desktop Connections)

#3

see additional instructions above
(also have to run** dbus-launch vncserver **again since is not configured for start on boot yet)

#4

Hallo Zusammen,

ich hatte das selbe Problem: vncviewer blendet kurz den Login-Screen auf und
die Verbindung bricht dann ab mit folgenden Fehlermeldungen:

Client:

vncviewer: VNC server closed connection

Server:

xinetd[684]: START: vnc1 from=192.168.1.100
localhost:1[11187]: Abnormal termination of greeter for display localhost:1, code 1, signal 0
xinetd[684]: EXIT: vnc1 status=0 duration=2(sec)

Nach viel lesen, ausprobieren etc. bin ich darauf gekommen, dass beim Server IPv6 enabled
ist, das Netzwerk aber ingesamt mit allen Maschinen IPv4.

Nachdem ich unter Yast->Network Settings -> IPv6 Protocol Settings “unchecked” habe,
geniesse ich wieder eine stabile Verbindung zu diesem System.