Hey,
i want to install Synce 0.12. I download all packages from the Sourceforge-Site. When I run ./configure at libsynce Source configure said no DBUS found.
checking for DBUS... no
configure: error: odccm support requested but D-BUS could not be found
I use openSUSE 11 with GNOME-Desktop and I need Synce for Multisync to syncronize my HTC TyTN (Windows Mobile 6) with Evolution.
Thanks, Kai Opalka
I am using suse 11.0 with kde4 and installed synce package as well.
I have the problem that it is reconized by Hardware Abstraction Layer (according to yast hardware inspection)
Output:
1: udi = ‘/org/freedesktop/Hal/devices/net_80_00_60_0f_e8_00’
linux.subsystem = ‘net’
info.subsystem = ‘net’
org.freedesktop.Hal.Device.WakeOnLan.method_signatures = { ‘’, ‘’, ‘b’ }
info.product = ‘Networking Interface’
org.freedesktop.Hal.Device.WakeOnLan.method_argnames = { ‘’, ‘’, ‘enable’ }
info.udi = ‘/org/freedesktop/Hal/devices/net_80_00_60_0f_e8_00’
info.interfaces = { ‘org.freedesktop.Hal.Device.WakeOnLan’ }
org.freedesktop.Hal.Device.WakeOnLan.method_execpaths = { ‘hal-system-wol-supported’, ‘hal-system-wol-enabled’, ‘hal-system-wol-enable’ }
info.category = ‘net.80203’
net.originating_device = ‘/org/freedesktop/Hal/devices/usb_device_ffffffff_ffffffff_noserial’
info.capabilities = { ‘net’, ‘net.80203’, ‘wake_on_lan’ }
net.interface = ‘rndis0’
But if i run ifconfig it doesn’t show.
after installing synce 0.12, turning on the plug-in’s as described at the opensuse item site. no connection is made…
iḿ running opensuse 11.1
handheld glofiish x500 windows mobile 6.1 cooked.
the next connection report is given
pdsdijkstra@linux-wpol:~> pls
** Message: Device /org/freedesktop/Hal/devices/usb_device_1066_ce_7abf5000_4967_0801_0000_000000000000_if0_serial_usb_0 not fully set in Hal, skipping
** Message: Odccm is not running, ignoring
pls: Could not find configuration at path ‘(Default)’
>:(
is there anybody out there ?
i’m linux beginner…
Did you install usb-rndis-lite-kmp, and important have you configured then eth1 (your mobile) as mentioned on the Synce-opensuse site.
You also have to adjust your firewall settings.
So, as a first trial, I would just disable the firewall, then try to sync again.
Can you browse your mobile with Konquerer; rapip:/
after installing synce 0.12, turning on the plug-in’s as described at
the opensuse item site. no connection is made…
iḿ running opensuse 11.1
handheld glofiish x500 windows mobile 6.1 cooked.
the next connection report is given
> pdsdijkstra@linux-wpol:~> pls
> ** Message: Device
> /org/freedesktop/Hal/devices/usb_device_1066_ce_7abf5000_4967_0801_0000_000000000000_if0_serial_usb_0
> not fully set in Hal, skipping
> ** Message: Odccm is not running, ignoring
> pls: Could not find configuration at path ‘(Default)’
>
>:(
is there anybody out there ?
i’m linux beginner…
pdsdijkstra’s Profile: http://forums.opensuse.org/member.php?userid=20866
View this thread: http://forums.opensuse.org/showthread.php?t=395866
Did you install usb-rndis-lite-kmp, and important have you configured
then eth1 (your mobile) as mentioned on the Synce-opensuse site.
You also have to adjust your firewall settings.
So, as a first trial, I would just disable the firewall, then try to
sync again.
Can you browse your mobile with Konquerer; rapip:/
swannema’s Profile: http://forums.opensuse.org/member.php?userid=186
View this thread: http://forums.opensuse.org/showthread.php?t=395866