New laptop, SUSE 11, don't see my wireless card...

Could you please help me too please? I have the same problem of my new laptop not recognizing my wireless card as the other guy in a previous thread.
I have run all the commands that you’ve (swerdna) posted for the other user and here are my results. Thank you in advance!

linux-rccc:/home/jlee # lspci
00:00.0 Host bridge: Intel Corporation Mobile 945GME Express Memory Controller H
ub (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 945GME Express Integ
rated Graphics Controller (rev 03)
00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML E
xpress Integrated Graphics Controller (rev 03)
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Aud
io Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (r
ev 02)
00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (r
ev 02)
00:1c.2 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3 (r ev 02)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controll er #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controll er #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controll er #3 (rev 02)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controll er #4 (rev 02)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Control ler (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (re v 02)
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (re v 02)
00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Con troller (rev 02)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 02)
02:00.0 Ethernet controller: Broadcom Corporation NetLink BCM5906M Fast Ethernet PCI Express (rev 02)
05:00.0 Network controller: Broadcom Corporation BCM4310 USB Controller (rev 01)
linux-rccc:/home/jlee # lspci -nn | egrep “thernet|theros”
02:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM5906M Fast Ethernet PCI Express [14e4:1713] (rev 02)
linux-rccc:/home/jlee # rpm -qa | egrep “madwifi|ndiswrapper”
linux-rccc:/home/jlee # uname -r
2.6.25.18-0.2-default
linux-rccc:/home/jlee # iwconfig
lo no wireless extensions.

eth0 no wireless extensions.

linux-rccc:/home/jlee # ifconfig
eth0 Link encap:Ethernet HWaddr 00:1E:68:AF:61:03
inet addr:192.168.0.100 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::21e:68ff:feaf:6103/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:3477 errors:0 dropped:0 overruns:0 frame:0
TX packets:2396 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2104662 (2.0 Mb) TX bytes:529155 (516.7 Kb)
Interrupt:16

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:220 errors:0 dropped:0 overruns:0 frame:0
TX packets:220 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:13872 (13.5 Kb) TX bytes:13872 (13.5 Kb)

linux-rccc:/home/jlee # ndiswrapper -l
bash: ndiswrapper: command not found
linux-rccc:/home/jlee # lsmod | egrep ath
linux-rccc:/home/jlee #

I note you have a Broadcom BCM4310, which I think is your wireless.

I think < not sure > with Broadcom wireless devices, there are two approaches that can be taken:
a. install custom firmware (not available/setup for all broadcom devices); or
b. use ndiswrapper (which in essence is software that wraps around a windows driver, allowing one to use the windows driver - the problem being sometimes there are unexpected effects).

I note there is a thread here for the BCM4310:
Broadcom 4310 on XPS M1330 - openSUSE Forums

I have no experience with this, so I can not provide help myself.

For the BCM4310 USB device, which is PCIe - not USB - based, the native driver
will not work. We are working on the reverse engineering but it will be some
time. The thread to which oldcpu referred you is a good one. The critical parts
for using ndiswrapper is to get the Win XP driver - the Vista one doesn’t work,
and to get a 32- or 64-bit driver according to your system.

Larry