lan card driver not work

In new Acer Extensa 5635G i install 11.2 but lan card don`t work,wireles too!Hеrе info

/sbin/lspci

07:00.0 Network controller: Intel Corporation Wireless WiFi Link 5100
09:00.0 Ethernet controller: Attansic Technology Corp. Device 1063 (rev c0)

/usr/sbin/hwinfo

32: PCI 700.0: 0280 Network controller
  [Created at pci.318]                
  UDI: /org/freedesktop/Hal/devices/pci_8086_4232
  Unique ID: aK5u.PDTfCPuk4g7                    
  Parent ID: Z7uZ.C0MkgLA2c85                    
  SysFS ID: /devices/pci0000:00/0000:00:1c.3/0000:07:00.0
  SysFS BusID: 0000:07:00.0                              
  Hardware Class: network                                
  Model: "Intel Wireless WiFi Link 5100"                 
  Vendor: pci 0x8086 "Intel Corporation"                 
  Device: pci 0x4232 "Wireless WiFi Link 5100"           
  SubVendor: pci 0x8086 "Intel Corporation"              
  SubDevice: pci 0x1201                                  
  Memory Range: 0xbe000000-0xbe001fff (rw,non-prefetchable,disabled)
  IRQ: 10 (no events)                                               
  Module Alias: "pci:v00008086d00004232sv00008086sd00001201bc02sc80i00"
  Driver Info #0:                                                      
    Driver Status: iwlagn is not active                                
    Driver Activation Cmd: "modprobe iwlagn"                           
  Config Status: cfg=no, avail=yes, need=no, active=unknown            
  Attached to: #19 (PCI bridge)                                        

33: PCI 900.0: 0200 Ethernet controller
  [Created at pci.318]                 
  UDI: /org/freedesktop/Hal/devices/pci_1969_1063
  Unique ID: x1VA.TtUhpoSqTa9                    
  Parent ID: HnsE.Gg7kbdesig6                    
  SysFS ID: /devices/pci0000:00/0000:00:1c.5/0000:09:00.0
  SysFS BusID: 0000:09:00.0                              
  Hardware Class: network                                
  Model: "Attansic Ethernet controller"                  
  Vendor: pci 0x1969 "Attansic Technology Corp."         
  Device: pci 0x1063                                     
  SubVendor: pci 0x1025 "Acer Incorporated [ALI]"        
  SubDevice: pci 0x0253                                  
  Revision: 0xc0                                         
  Memory Range: 0xbe100000-0xbe13ffff (rw,non-prefetchable)
  I/O Ports: 0x3000-0x3fff (rw,disabled)                   
  IRQ: 17 (no events)                                      
  Module Alias: "pci:v00001969d00001063sv00001025sd00000253bc02sc00i00"
  Driver Info #0:                                                      
    Driver Status: atl1c is active                                     
    Driver Activation Cmd: "modprobe atl1c"                            
  Config Status: cfg=no, avail=yes, need=no, active=unknown            
  Attached to: #20 (PCI bridge)  

/sbin/lspci -n

07:00.0 0280: 8086:4232
09:00.0 0200: 1969:1063 (rev c0)

/sbin/ifconfig -a 


lo        Link encap:Local Loopback                                                                        
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:126 errors:0 dropped:0 overruns:0 frame:0
          TX packets:126 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:8660 (8.4 Kb)  TX bytes:8660 (8.4 Kb)

pan0      Link encap:Ethernet  HWaddr 16:73:CA:03:E8:51
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)


lsmod

iwlcore               204964  0                                                                                                       
mac80211              217656  1 iwlcore  
cfg80211              103424  2 iwlcore,mac80211  
atl1c                  38852  0          

Sam gay tell my ,i mast change something in /etc/network/interfaces but i can`t find this file !
First of all let wired lan work,wireles lаter…
Please help my!

He was an Ubuntu or Debian user. On openSUSE, nic configurations are written in /etc/sysconfig/network/ifcfg-ethX files.

Or configure it with YaST.

I tray with YaST but button is gray,also i tray to make one ifcfg-eth0 file but what is next because this not change status in YAST

http://forums.opensuse.org/network-internet/416814-opensuse11-cant-detect-bcm5751m-ethernet-card-my-ibm-t43.html#post2117913
please see this I think it is similar

Look at this Arch Linux Forums / Wireless and ethernet broken