Trying to get the FM section if the above card (kworld/tevion DVB-T 220RF) working with kradio in 11.1/KDE4 using kradio/KDE3. It DOES appear to be working, as in kradio recognises the card, and can search for and find real stations, but, I then get no sound, and checking dmesg, there are multiple entries saying:
saa7133[0]: dsp access error
The loading messages in dmesg are:*
saa7130/34: v4l2 driver version 0.2.14 loaded
vendor=8086 device=244e
saa7134 0000:05:00.0: PCI INT A → GSI 16 (level, low) → IRQ 16
saa7133[0]: found at 0000:05:00.0, rev: 208, irq: 16, latency: 64, mmio: 0xfebff800
saa7133[0]: subsystem: 17de:7201, board: Tevion/KWorld DVB-T 220RF [card=88,autodetected]
resource map sanity check conflict 0xfebff800 0xfec007ff 0xfeb00000 0xfebfffff PCI Bus 0000:05
------------ cut here ]------------
WARNING: at arch/x86/mm/ioremap.c:156 _ioremap_caller+0xc8/0x369()
Modules linked in: saa7134(+) ir_common snd_hda_intel snd_pcm snd_timer gspca_main v4l2_common videobuf_dma
sg sr_mod snd_page_alloc compat_ioctl32 i2c_i801 videodev videobuf_core snd_hwdep r8169 rtc_cmos rtc_core tv
eeprom ppdev snd rtc_lib mii v4l1_compat ohci1394 intel_agp button cdrom i2c_core usb_storage soundcore parp
ort_pc serio_raw joydev ieee1394 pcspkr parport sg usbhid hid ff_memless ehci_hcd uhci_hcd sd_mod crc_t10dif
usbcore edd ext3 mbcache jbd fan ide_pci_generic ide_core ata_generic ata_piix pata_marvell ahci libata scs
i_mod dock thermal processor thermal_sys hwmon
Supported: Yes
Pid: 1376, comm: modprobe Not tainted 2.6.27.7-9-default #1
Call Trace:
<ffffffff8020e42e>] show_trace_log_lvl+0x41/0x58
<ffffffff804a1e97>] dump_stack+0x69/0x6f
<ffffffff80240eb2>] warn_on_slowpath+0x51/0x77
<ffffffff80228ab4>] __ioremap_caller+0xc8/0x369
<ffffffffa032f699>] saa7134_initdev+0x429/0x874 [saa7134]
<ffffffff8037a89b>] pci_device_probe+0xb8/0x105
<ffffffff803eddc3>] really_probe+0xdd/0x1e5
<ffffffff803edfb0>] __driver_attach+0x46/0x6d
<ffffffff803ed555>] bus_for_each_dev+0x44/0x78
<ffffffff803ece3b>] bus_add_driver+0xef/0x235
<ffffffff803ee174>] driver_register+0xa2/0x11f
<ffffffff8037ab43>] __pci_register_driver+0x5d/0x8e
<ffffffff80209041>] _stext+0x41/0x11d
<ffffffff80265ec9>] sys_init_module+0xa0/0x1ba
<ffffffff8020c37a>] system_call_fastpath+0x16/0x1b
<00007f341396a76a>] 0x7f341396a76a
— end trace 089ed8d5841c83f0 ]—
saa7133[0]: board init: gpio is 100
gspca: probing 046d:092f
saa7133[0]: i2c eeprom 00: de 17 01 72 ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 50:<6>gspca: probe ok
usbcore: registered new interface driver spca561
spca561: registered
ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
tuner’ 1-004b: chip found @ 0x96 (saa7133[0])
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011d80001865103]
tda829x 1-004b: setting tuner address to 61
tda829x 1-004b: type set to tda8290+75a
saa7133[0]: registered device video1 [v4l2]
saa7133[0]: registered device vbi0
saa7133[0]: registered device radio0
DVB: registering new adapter (saa7133[0])
DVB: registering frontend 0 (Philips TDA10046H DVB-T)…
tda1004x: setting up plls for 48MHz sampling clock
tda1004x: found firmware revision 23 – ok*
Looks like there is an error here, but I certainly don’t understand it… :’(
Help please…
Thanks, John.
)