kernel panic when booting openSUSE 11 RC1 x86

English Install/Boot/Login
1

Hi,
I’ve been attempt to boot openSUSE 11 RC1 x86
Gnome liveCd. But it encountered kernel panic!

Can anyone help me?
Thanks!

Here is the serial port log:

Freeing unused kernel memory: 256k freed
Write protecting the kernel read-only data: 1440k
Loading KIWI CD Boot-System…

Creating device nodes with udev

Boot logging started on /dev/ttyS0(/dev/console) at Tue Jun 17 10:47:04 2008

-----> Starting boot shell on tty2

-----> Boot-Logging enabled on /dev/tty3

-----> Kernel logging enabled on: /dev/tty4

-----> Including required kernel modules…

-----> Probing module: ata_piix
No dock devices found.

SCSI subsystem initialized
ACPI: PCI Interrupt 0000:00:1f.2** -> GSI 19 (level, low) -> IRQ 19
ata_piix 0000:00:1f.2: MAP P0 P2 P1 P3 ]
scsi0 : ata_piix
scsi1 : ata_piix
ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xff90 irq 14
ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xff98 irq 15
ata1: SATA link down (SStatus 0 SControl 300)
ata2: SATA link down (SStatus 0 SControl 300)
ACPI: PCI Interrupt 0000:00:1f.5** -> GSI 19 (level, low) -> IRQ 19
ata_piix 0000:00:1f.5: MAP P0 – P1 – ]
scsi2 : ata_piix
scsi3 : ata_piix
ata3: SATA max UDMA/133 cmd 0xcc00 ctl 0xc880 bmdma 0xc400 irq 19
ata4: SATA max UDMA/133 cmd 0xc800 ctl 0xc480 bmdma 0xc408 irq 19
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: ATAPI: HL-DT-STDVD-ROM GDRH20N, D8E4, max UDMA/100
ata3.00: configured for UDMA/100
ata4: SATA link down (SStatus 0 SControl 300)
CPU 1: Machine Check Exception: 0000000000000004
CPU 2: Machine Check Exception: 0000000000000004
CPU 0: Machine Check Exception: 0000000000000004
Kernel panic - not syncing: Unable to continue
Kernel panic - not syncing: Unable to continue

2

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Can you post what happens before it up until the panic?

Good luck.

YutingChou wrote:
| Hi,
| I’ve been attempt to boot openSUSE 11 RC1 x86
| Gnome liveCd. But it encountered kernel panic!
|
| Can anyone help me?
| Thanks!
|
| Here is the serial port log:
|> Freeing unused kernel memory: 256k freed
|> Write protecting the kernel read-only data: 1440k
|> Loading KIWI CD Boot-System…
|> ------------------------------
|> Creating device nodes with udev
|>
|> Boot logging started on /dev/ttyS0(/dev/console) at Tue Jun 17 10:47:04
|> 2008
|>
|> -----> Starting boot shell on tty2
|>
|> -----> Boot-Logging enabled on /dev/tty3
|>
|> -----> Kernel logging enabled on: /dev/tty4
|>
|> -----> Including required kernel modules…
|>
|> -----> Probing module: ata_piix
|> No dock devices found.
|>
|> SCSI subsystem initialized
|> ACPI: PCI Interrupt 0000:00:1f.2** → GSI 19 (level, low) → IRQ 19
|> ata_piix 0000:00:1f.2: MAP P0 P2 P1 P3 ]
|> scsi0 : ata_piix
|> scsi1 : ata_piix
|> ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xff90 irq 14
|> ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xff98 irq 15
|> ata1: SATA link down (SStatus 0 SControl 300)
|> ata2: SATA link down (SStatus 0 SControl 300)
|> ACPI: PCI Interrupt 0000:00:1f.5** → GSI 19 (level, low) → IRQ 19
|> ata_piix 0000:00:1f.5: MAP P0 – P1 – ]
|> scsi2 : ata_piix
|> scsi3 : ata_piix
|> ata3: SATA max UDMA/133 cmd 0xcc00 ctl 0xc880 bmdma 0xc400 irq 19
|> ata4: SATA max UDMA/133 cmd 0xc800 ctl 0xc480 bmdma 0xc408 irq 19
|> ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
|> ata3.00: ATAPI: HL-DT-STDVD-ROM GDRH20N, D8E4, max UDMA/100
|> ata3.00: configured for UDMA/100
|> ata4: SATA link down (SStatus 0 SControl 300)
|> CPU 1: Machine Check Exception: 0000000000000004
|> CPU 2: Machine Check Exception: 0000000000000004
|> CPU 0: Machine Check Exception: 0000000000000004
|> Kernel panic - not syncing: Unable to continue
|> Kernel panic - not syncing: Unable to continue
|
|
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.2 (GNU/Linux)
Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org

iD8DBQFIVz0R3s42bA80+9kRAk9bAJ0ZPpoyW/cYq2rPKRBJzDF4NzNliACeIOB2
RhuyiUrl2HbY21f8w1JU6a4=
=JiwR
-----END PGP SIGNATURE-----

3

Here is the whole log part1:

inux version 2.6.25.4-8-default (geeko@buildhost) (gcc version 4.3.1 20080507 (prerelease) [gcc-4_3-branch revision 135036] (SUSE Linux) ) #1 SMP 2008-05-26 15:23:05 +0200
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007fe60000 (usable)
BIOS-e820: 000000007fe6e000 - 000000007fe70000 type 9
BIOS-e820: 000000007fe70000 - 000000007fe7e000 (ACPI data)
BIOS-e820: 000000007fe7e000 - 000000007fed0000 (ACPI NVS)
BIOS-e820: 000000007fed0000 - 000000007fee0000 (reserved)
BIOS-e820: 000000007fee6000 - 0000000080000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
1150MB HIGHMEM available.
896MB LOWMEM available.
Scan SMP from c0000000 for 1024 bytes.
Scan SMP from c009fc00 for 1024 bytes.
Scan SMP from c00f0000 for 65536 bytes.
found SMP MP-table at [c00ff780] 000ff780
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 523872
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 523872
DMI present.
Using APIC driver default
ACPI: RSDP 000F9B10, 0014
ACPI: RSDT 7FE70000, 0050
ACPI: FACP 7FE70200, 0084
ACPI: DSDT 7FE706D0, 5C53
ACPI: FACS 7FE7E000, 0040
ACPI: APIC 7FE70390, 00D2
ACPI: MCFG 7FE704C0, 003C
ACPI: SPMI 7FE70500, 0041
ACPI: SLIC 7FE70550, 0176
ACPI: OEMB 7FE7E040, 0072
ACPI: SSDT 7FE7E8C0, 23DF
ACPI: EINJ 7FE786D0, 0130
ACPI: BERT 7FE78860, 0030
ACPI: ERST 7FE78890, 01B0
ACPI: HEST 7FE78A40, 00A8
ACPI: PM-Timer IO Port: 0x808
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x10] enabled)
Processor #16 7:10 APIC version 21
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x12] enabled)
Processor #18 7:10 APIC version 21
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x14] enabled)
Processor #20 7:10 APIC version 21
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x16] enabled)
Processor #22 7:10 APIC version 21
ACPI: LAPIC (acpi_id[0x05] lapic_id[0x84] disabled)
ACPI: LAPIC (acpi_id[0x06] lapic_id[0x85] disabled)
ACPI: LAPIC (acpi_id[0x07] lapic_id[0x86] disabled)
ACPI: LAPIC (acpi_id[0x08] lapic_id[0x87] disabled)
ACPI: LAPIC (acpi_id[0x09] lapic_id[0x88] disabled)
ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x89] disabled)
ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x8a] disabled)
ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x8b] disabled)
ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x8c] disabled)
ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x8d] disabled)
ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x8e] disabled)
ACPI: LAPIC (acpi_id[0x10] lapic_id[0x8f] disabled)
ACPI: LAPIC_NMI (acpi_id[0xff] high dfl lint[0x1])
ACPI: IOAPIC (id[0x17] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 23, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 519780
Kernel command line: BOOT_IMAGE=linux initrd=initrd,10240768.spl ramdisk_size=512000 ramdisk_blocksize=4096 splash=silent vga=0x317 console=tty0 console=ttyS0,115200 splash=verbose
bootsplash: silent mode.
bootsplash: verbose mode.
Enabling fast FPU save and restore… done.
Enabling unmasked SIMD FPU exception support… done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 2133.453 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
console [ttyS0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 2059256k/2095488k available (1945k kernel code, 35028k reserved, 1629k data, 256k init, 1177984k highmem)
virtual kernel memory layout:
fixmap : 0xffdf2000 - 0xfffff000 (2100 kB)
pkmap : 0xff400000 - 0xff800000 (4096 kB)
vmalloc : 0xf8800000 - 0xff3fe000 ( 107 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc0485000 - 0xc04c5000 ( 256 kB)
.data : 0xc02e64ad - 0xc047d96c (1629 kB)
.text : 0xc0100000 - 0xc02e64ad (1945 kB)
Checking if this processor honours the WP bit even in supervisor mode…Ok.
Calibrating delay using timer specific routine… 4270.56 BogoMIPS (lpj=8541125)
Security Framework initialized
AppArmor: AppArmor initialized <NULL>
AppArmor: Registered secondary security module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 4096K
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
using mwait in idle threads.
Compat vDSO mapped to ffffe000.
Checking ‘hlt’ instruction… OK.
ACPI: Core revision 20070126
ACPI: Checking initramfs for custom DSDT
Parsing all Control Methods:
Table [DSDT](id 0001) - 828 Objects with 76 Devices 203 Methods 27 Regions
Parsing all Control Methods:
Table [SSDT](id 0002) - 127 Objects with 0 Devices 32 Methods 1 Regions
tbxface-0598 [00] tb_load_namespace : ACPI Tables successfully acquired
evxfevnt-0091 [00] enable : Transition to ACPI mode successful
CPU0: Intel Genuine Intel(R) CPU @ 0000 @ 2.13GHz stepping 02
Booting processor 1/18 ip 4000
Initializing CPU#1
Calibrating delay using timer specific routine… 4267.09 BogoMIPS (lpj=8534196)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 4096K
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 1
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Genuine Intel(R) CPU @ 0000 @ 2.13GHz stepping 02
Booting processor 2/20 ip 4000
Initializing CPU#2
Calibrating delay using timer specific routine… 4267.10 BogoMIPS (lpj=8534211)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 4096K
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 2
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#2.
CPU2: Intel Genuine Intel(R) CPU @ 0000 @ 2.13GHz stepping 02
Booting processor 3/22 ip 4000
Initializing CPU#3
Calibrating delay using timer specific routine… 4267.09 BogoMIPS (lpj=8534194)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 4096K
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 3
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#3.
CPU3: Intel Genuine Intel(R) CPU @ 0000 @ 2.13GHz stepping 02
Total of 4 processors activated (17071.86 BogoMIPS).
ENABLING IO-APIC IRQs
…TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization [CPU#0 -> CPU#1]:
Measured 72 cycles TSC warp between CPUs, turning off TSC clock.
Marking TSC unstable due to: check_tsc_sync_source failed.
Brought up 4 CPUs
net_namespace: 548 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG for extended config space
PCI: Using configuration type 1
Setting up standard PCI resources
evgpeblk-0956 [00] ev_create_gpe_block : GPE 00 to 3F [_GPE] 8 regs on int 0x9
evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 10 Wake, Enabled 1 Runtime GPEs in this block
Completing Region/Field/Buffer/Package initialization:…
Initialized 23/28 Regions 43/43 Fields 53/53 Buffers 33/35 Packages (964 nodes)
Initializing Device/Processor/Thermal objects by executing _INI methods:
Executed 0 _INI methods requiring 0 _STA executions (examined 94 objects)
ACPI: Interpreter enabled
ACPI: (supports S0 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs *5)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 *7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 6 7 *10 11 12 14 15)
ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - F8, should be F7 [20070126]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn’t work, try “pci=routeirq”. If it helps, post a report
AppArmor: AppArmor Filesystem Enabled
ACPI: RTC can wake from S4
system 00:01: iomem range 0xfc000000-0xfcffffff has been reserved
system 00:01: iomem range 0xfd000000-0xfdffffff has been reserved
system 00:01: iomem range 0xfe000000-0xfebfffff has been reserved

4

Here is the part2:

system 00:07: ioport range 0xa00-0xa7f has been reserved
system 00:07: ioport range 0xa80-0xa83 has been reserved
system 00:07: ioport range 0xa84-0xa85 has been reserved
system 00:07: ioport range 0xa86-0xa8d has been reserved
system 00:07: ioport range 0xa90-0xa9f has been reserved
system 00:07: ioport range 0xb00-0xbfe has been reserved
system 00:08: ioport range 0xca4-0xca5 has been reserved
system 00:08: ioport range 0xca7-0xca8 has been reserved
system 00:08: ioport range 0xca0-0xca0 has been reserved
system 00:08: ioport range 0xca1-0xca1 has been reserved
system 00:08: ioport range 0xca2-0xca2 has been reserved
system 00:08: ioport range 0xca3-0xca3 has been reserved
system 00:08: ioport range 0x4d0-0x4d1 has been reserved
system 00:08: ioport range 0x800-0x87f has been reserved
system 00:08: ioport range 0x500-0x53f has been reserved
system 00:08: iomem range 0xffa00000-0xfffffffe could not be reserved
system 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved
system 00:08: iomem range 0xfed20000-0xfed44fff has been reserved
system 00:08: iomem range 0xfed45000-0xfed9ffff has been reserved
system 00:08: iomem range 0xfed20000-0xfed3ffff has been reserved
system 00:08: iomem range 0xfed40000-0xfed8ffff could not be reserved
system 00:09: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:09: iomem range 0xfee00000-0xfee00fff could not be reserved
system 00:0a: iomem range 0xe0000000-0xefffffff could not be reserved
system 00:0d: iomem range 0x0-0x9ffff could not be reserved
system 00:0d: iomem range 0xc0000-0xcffff could not be reserved
system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
system 00:0d: iomem range 0x100000-0x7fffffff could not be reserved
system 00:0d: iomem range 0xfed90000-0xffffffff could not be reserved
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:03.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:07.0
IO window: e000-efff
MEM window: 0xfaf00000-0xfaffffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:09.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.4
IO window: disabled.
MEM window: 0xfb000000-0xfbffffff
PREFETCH window: 0x00000000f9000000-0x00000000f9ffffff
PCI: Bridge: 0000:00:1c.5
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 16 (level, low) -> IRQ 16
ACPI: PCI Interrupt 0000:00:1c.5** -> GSI 17 (level, low) -> IRQ 17
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Unpacking initramfs… done
Freeing initrd memory: 13286k freed
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
type=2000 audit(1213699604.004:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
assign_interrupt_mode Found MSI capability
assign_interrupt_mode Found MSI capability
assign_interrupt_mode Found MSI capability
assign_interrupt_mode Found MSI capability
assign_interrupt_mode Found MSI capability
assign_interrupt_mode Found MSI capability
assign_interrupt_mode Found MSI capability
vesafb: framebuffer at 0xf9000000, mapped to 0xf8880000, using 6144k, total 8128k
vesafb: mode is 1024x768x16, linelength=2048, pages=4
vesafb: protected mode interface info at c000:7b20
vesafb: pmi: set display start = c00c7bb2, set palette = c00c7c1e
vesafb: pmi: ports = 3de 3df
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture…
bootsplash: silentjpeg size 166113 bytes
bootsplash: …found (1024x768, 197662 bytes, v3).
Console: switching to colour frame buffer device 124x44
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards…
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
PNP: No PS/2 controller found. Probing ports directly.
Failed to disable AUX port, but continuing anyway… Is this a SiS?
If AUX port is really absent please use the ‘i8042.noaux’ option.
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: PC Speaker as /devices/platform/pcspkr/input/input0
cpuidle: using governor ladder
cpuidle: using governor menu
NET: Registered protocol family 1
Using IPI No-Shortcut mode
registered taskstats version 1
Freeing unused kernel memory: 256k freed
Write protecting the kernel read-only data: 1440k
Loading KIWI CD Boot-System…

Creating device nodes with udev

Boot logging started on /dev/ttyS0(/dev/console) at Tue Jun 17 10:47:04 2008

-----> Starting boot shell on tty2

-----> Boot-Logging enabled on /dev/tty3

-----> Kernel logging enabled on: /dev/tty4

-----> Including required kernel modules…

-----> Probing module: ata_piix
No dock devices found.

SCSI subsystem initialized
ACPI: PCI Interrupt 0000:00:1f.2** -> GSI 19 (level, low) -> IRQ 19
ata_piix 0000:00:1f.2: MAP P0 P2 P1 P3 ]
scsi0 : ata_piix
scsi1 : ata_piix
ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xff90 irq 14
ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xff98 irq 15
ata1: SATA link down (SStatus 0 SControl 300)
ata2: SATA link down (SStatus 0 SControl 300)
ACPI: PCI Interrupt 0000:00:1f.5** -> GSI 19 (level, low) -> IRQ 19
ata_piix 0000:00:1f.5: MAP P0 – P1 – ]
scsi2 : ata_piix
scsi3 : ata_piix
ata3: SATA max UDMA/133 cmd 0xcc00 ctl 0xc880 bmdma 0xc400 irq 19
ata4: SATA max UDMA/133 cmd 0xc800 ctl 0xc480 bmdma 0xc408 irq 19
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: ATAPI: HL-DT-STDVD-ROM GDRH20N, D8E4, max UDMA/100
ata3.00: configured for UDMA/100
ata4: SATA link down (SStatus 0 SControl 300)
CPU 1: Machine Check Exception: 0000000000000004
CPU 2: Machine Check Exception: 0000000000000004
CPU 0: Machine Check Exception: 0000000000000004
Kernel panic - not syncing: Unable to continue
Kernel panic - not syncing: Unable to continue