I Need help in my network

i just install Linux 11.1 and evry thing just work fine
but when am try to “make connect with Win network
by using NetworkMANAGER (wlan-wire)” it never establish
i try samba same think
The wire network work very good in Suse 9 no problem
i have Aser Extensa 5220
wire net (Broadcom NetLink ™ Gigabit Ethernet)
Wireless net (Athero AR5007EG)
plezzz help

((((Wirless)))
host is the script executed?
— (1) LinuxClient
— WLAN SSID to connect to: §§§§§§§§1

— NWEliza is analyzing the system for common network configuration errors …

!!! CND0120E: Network card wlan0 has no IP address
!!! CND0500W: Channel 10 used by your accesspoint is also used by 1 other access points
!!! CND0230W: IPV6 enabled
!!! CND0310W: Classic network configuration with ifup was detected. Configuration with knetworkmanager is much easier

(((Wire)))

— NWEliza is analyzing the system for common network configuration errors …

!!! CND0120E: Network card eth0 has no IP address
!!! CND0230W: IPV6 enabled
!!! CND0310W: Classic network configuration with ifup was detected. Configuration with knetworkmanager is much easier

==================================================================================================================
*** ifconfig
eth0 Link encap:Ethernet HWaddr ##:##:##:##:##:#1
inet6 addr: fe80::21d:72ff:fe24:efa0/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:11 errors:0 dropped:0 overruns:0 frame:0
TX packets:152 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2696 (2.6 Kb) TX bytes:51532 (50.3 Kb)
Interrupt:16
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:460 errors:0 dropped:0 overruns:0 frame:0
TX packets:460 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:32456 (31.6 Kb) TX bytes:32456 (31.6 Kb)
wlan0 Link encap:Ethernet HWaddr ##:##:##:##:##:#2
inet6 addr: fe80::217:c4ff:fe1a:28d4/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:934 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:328440 (320.7 Kb)
wmaster0 Link encap:UNSPEC HWaddr 00-17-C4-1A-28-D4-38-64-00-00-00-00-00-00-00-00
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

*** ping tests
connect: Network is unreachable
Ping of 195.135.220.3 failed
ping: unknown host Linux-Betriebssystem | SUSE Linux Enterprise
Ping of Linux-Betriebssystem | SUSE Linux Enterprise failed

*** dhcpcd-test
wlan0: No DHCP server detected info, wlan0: hardware address = ##:##:##:##:##:#2
info, wlan0: broadcasting for a lease
debug, wlan0: sending DHCP_DISCOVER with xid 0x2b7ea3fe
debug, wlan0: waiting for 3 seconds
info, wlan0: exiting

*** lspci
02:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM5787M Gigabit Ethernet PCI Express [14e4:1693] (rev 02)
04:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter [168c:001c] (rev 01)

*** lsusb
Bus 007 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 002: ID 5986:0102 Acer, Inc Crystal Eye Webcam
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 002: ID 0421:0420 Nokia Mobile Phones
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

*** hwinfo (filtered)
27: PCI 200.0: 0200 Ethernet controller
Model: “Broadcom NetLink BCM5787M Gigabit Ethernet PCI Express”
Vendor: pci 0x14e4 “Broadcom”
Device: pci 0x1693 “NetLink BCM5787M Gigabit Ethernet PCI Express”
SubVendor: pci 0x1025 “Acer Incorporated [ALI]”
SubDevice: pci 0x011c
Driver: “tg3”
Driver Modules: “tg3”
Device File: eth0
Link detected: yes
Driver Status: tg3 is active
Driver Activation Cmd: “modprobe tg3”
28: PCI 400.0: 0282 WLAN controller
Model: “Atheros AR242x 802.11abg Wireless PCI Express Adapter”
Vendor: pci 0x168c “Atheros Communications Inc.”
Device: pci 0x001c “AR242x 802.11abg Wireless PCI Express Adapter”
SubVendor: pci 0x1a32
SubDevice: pci 0x0105
Driver: “ath5k_pci”
Driver Modules: “ath5k”
Device File: wlan0
Link detected: yes
Driver Status: ath5k is active
Driver Activation Cmd: “modprobe ath5k”

*** lsmod # (filtered)
| ac | acer_wmi | af_packet | agpgart | arc4 |
| ata_piix | ath5k | battery | binfmt_misc | cdc_acm |
| cdc_ether | cfg80211 | compat_ioctl32 | container | crc_ccitt |
| crc_t10dif | dock | drm | ecb | edd |
| ehci_hcd | fat | fuse | hwmon | i2c_core |
| i2c_i801 | i915 | iTCO_vendor_support| iTCO_wdt | ieee1394 |
| intel_agp | irda | jbd | led_class | libata |
| libphy | mac80211 | mbcache | mii | mmc_core |
| nls_cp437 | nls_iso8859_1 | nsc_ircc | ohci1394 | output |
| pcmcia_core | piix | rndis_host | rndis_wlan | rsrc_nonstatic |
| scsi_mod | sd_mod | sdhci | sdhci_pci | serio_raw |
| sg | snd_hda_intel | snd_hwdep | snd_seq_device | sr_mod |
| tg3 | thermal | thermal_sys | tifm_7xx1 | tifm_core |
| uhci_hcd | usbnet | uvcvideo | v4l1_compat | vfat |
| video | wmi | yenta_socket |

*** cat /etc/sysconfig/network/ifcfg-[earwd]*
— /etc/sysconfig/network/ifcfg-eth0
BOOTPROTO=‘dhcp’
BROADCAST=’’
ETHTOOL_OPTIONS=’’
IPADDR=’’
MTU=‘1500’
NAME=‘NetLink BCM5787M Gigabit Ethernet PCI Express’
NETMASK=’’
NETWORK=’’
REMOTE_IPADDR=’’
STARTMODE=‘ifcfg-eth0’
USERCONTROL=‘yes’
— /etc/sysconfig/network/ifcfg-eth0~
BOOTPROTO=‘dhcp’
BROADCAST=’’
ETHTOOL_OPTIONS=’’
IPADDR=’’
MTU=‘1500’
NAME=‘NetLink BCM5787M Gigabit Ethernet PCI Express’
NETMASK=’’
NETWORK=’’
REMOTE_IPADDR=’’
STARTMODE=‘auto’
USERCONTROL=‘yes’
— /etc/sysconfig/network/ifcfg-wlan0
BOOTPROTO=‘dhcp’
BROADCAST=’’
ETHTOOL_OPTIONS=’’
IPADDR=’’
MTU=’’
NAME=‘AR242x 802.11abg Wireless PCI Express Adapter’
NETMASK=’’
NETWORK=’’
REMOTE_IPADDR=’’
STARTMODE=‘auto’
USERCONTROL=‘yes’
WIRELESS_AP=’’
WIRELESS_AUTH_MODE=‘no-encryption’
WIRELESS_BITRATE=‘48’
WIRELESS_CA_CERT=’’
WIRELESS_CHANNEL=’’
WIRELESS_CLIENT_CERT=’’
WIRELESS_CLIENT_KEY=’’
WIRELESS_CLIENT_KEY_PASSWORD=’’
WIRELESS_DEFAULT_KEY=‘0’
WIRELESS_EAP_AUTH=’’
WIRELESS_EAP_MODE=’’
WIRELESS_ESSID=’§§§§§§§§2’
WIRELESS_FREQUENCY=’’
WIRELESS_KEY=’’
WIRELESS_KEY_0=’’
WIRELESS_KEY_1=’’
WIRELESS_KEY_2=’’
WIRELESS_KEY_3=’’
WIRELESS_KEY_LENGTH=’@@@@@@’
WIRELESS_MODE=‘Ad-hoc’
WIRELESS_NICK=’’
WIRELESS_NWID=’’
WIRELESS_PEAP_VERSION=’’
WIRELESS_POWER=‘yes’
WIRELESS_WPA_ANONID=’’
WIRELESS_WPA_IDENTITY=’’
WIRELESS_WPA_PASSWORD=’’
WIRELESS_WPA_PSK=’’
PREFIXLEN=‘24’

iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wmaster0 no wireless extensions.
irda0 no wireless extensions.
wlan0 IEEE 802.11bg ESSID:“2”
Mode:Ad-Hoc Frequency:2.412 GHz Cell:
Tx-Power=27 dBm
Retry min limit:7 RTS thr:off Fragment thr=2352 B
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0

*** Actual date for bias of following greps
05:00:01 2010-06-18

*** grep -i radio /var/log/messages* tail -n 5

*** dmesg | grep -i radio tail -n 5

*** tail -n 300 /var/log/messages* /usr/bin/grep -i firmware tail -n 5

*** ls /lib/firmware/*
2.6.27.7-9-pae 3CCFEM556.cis 3CXEM556.cis COMpad2.cis
COMpad4.cis DP83903.cis E-CARD.cis LA-PCM.cis
MT5634ZLX.cis NE2K.cis PCMLM28.cis PE-200.cis
PE520.cis RS-COM-2P.cis tamarack.cis

*** ndiswrapper -l
No ndiswrapper module loaded

*** Active processes
wpa_supplicant:NO knetworkmanager:NO nm-applet:NO

*** egrep -i “persistent|networkmanager” /etc/sysconfig/network/config grep -v “^# ^$”
NETWORKMANAGER=“no”

grep ‘eth|ath|wlan|ra’ /etc/udev/rules.d/net_persistent /etc/udev/rules.d/persistent-net
/etc/udev/rules.d/70-persistent-net.rules:SUBSYSTEM==“net”, ACTION==“add”, DRIVERS=="?", ATTR{address}=="##:##:##:##:##:#2", ATTR{type}==“1”, KERNEL=="wlan", NAME=“wlan0”
/etc/udev/rules.d/70-persistent-net.rules:SUBSYSTEM==“net”, ACTION==“add”, DRIVERS=="?", ATTR{address}=="##:##:##:##:##:#1", ATTR{type}==“1”, KERNEL=="eth", NAME=“eth0”

*** grep -r ‘eth-0-10-|ath-0-10-|wlan-0-10-|ra-0-10-’ /etc/modprobe.*
/etc/modprobe.conf:install eth0 /bin/true
/etc/modprobe.conf:install eth1 /bin/true

*** iwlist scanning
ESSID:"§§§§§§§§1"
Channel:10
Quality=60/100 Signal level:-64 dBm Noise level=-103 dBm
Encryption key:off
ESSID:"§§§§§§§§1"
Channel:10
Quality=64/100 Signal level:-62 dBm Noise level=-103 dBm
Encryption key:off

*** NWElizaStates
IF:eth0 IM:1 IF:wlan0 IM:2 DI:2 AP:1 FALON:1 NIC:1 cNiC:2:1 NI:1 cNI:1 NDIS:0 IP6:1 KM:0 WLW:0 RTDT:SuSE

Can we correctly assume this is a SLED install?