Hello
Running opensuse tubleweed w/kde, still kind of a linux noob.
boot takes a long time (30+ seconds on a SSD- pretty sure its related to wicked),but I have these errors on boot.
radeon 0000:01:00.0: VCE init error (-110)
sp5100_tco: I/O address 0x0cd6 already in use
I am using a asrock 970m pro3 motherboard with a r7-250 video card.
I also noticed the card may be running in 32 bit mode?
Apr 16 08:59:44 linux-fauk kernel: radeon 0000:01:00.0: VCE init error (-110).
Apr 16 08:59:44 linux-fauk kernel: [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
Apr 16 08:59:44 linux-fauk kernel: [drm] Driver supports precise vblank timestamp query.
Apr 16 08:59:44 linux-fauk kernel: radeon 0000:01:00.0: radeon: MSI limited to 32-bit
Apr 16 08:59:44 linux-fauk kernel: radeon 0000:01:00.0: radeon: using MSI.
Apr 16 08:59:44 linux-fauk kernel: [drm] radeon: irq initialized.
When I boot up, system updates do not work as I am “offline” may be related to the 2nd issue (or wicked)? (If I run manually they work fine)
Apr 16 08:59:46 linux-fauk kernel: AMD64 EDAC driver v3.4.0
Apr 16 08:59:46 linux-fauk kernel: EDAC amd64: DRAM ECC disabled.
Apr 16 08:59:46 linux-fauk kernel: EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
(Note that use of the override may cause unknown side effects.)
Apr 16 08:59:46 linux-fauk kernel: sp5100_tco: SP5100/SB800 TCO WatchDog Timer Driver v0.05
Apr 16 08:59:46 linux-fauk kernel: sp5100_tco: PCI Vendor ID: 0x1002, Device ID: 0x4385, Revision ID: 0x42
Apr 16 08:59:46 linux-fauk kernel: sp5100_tco: I/O address 0x0cd6 already in use
Apr 16 08:59:46 linux-fauk kernel: r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
Apr 16 08:59:46 linux-fauk kernel: r8169 0000:05:00.0: can't disable ASPM; OS doesn't have ASPM control
Apr 16 08:59:46 linux-fauk kernel: r8169 0000:05:00.0 eth0: RTL8168evl/8111evl at 0xffffc90001b5a000, d0:50:99:99:2f:ab, XID 0c900800 IRQ 31
Apr 16 08:59:46 linux-fauk kernel: r8169 0000:05:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
Apr 16 08:59:46 linux-fauk kernel: usbcore: registered new interface driver usbhid
my system log (journalctl) is filled with 200+ per second of this message (100,000+ lines per boot session)
linux-fauk org.kde.KScreen[2018]: kscreen: Primary output changed from KScreen::Output(Id: 82 , Name: "DVI-0" ) ( "DVI-0" ) to KScreen::Output(Id: 82 , Name: "DVI-0" ) ( "DVI-0" )
I guess, the questions are
- Are the errors on boot anything to worry about?
- is the
linux-fauk org.kde.KScreen[2018]: kscreen: Primary output changed from KScreen::Output(Id: 82 , Name: "DVI-0" ) ( "DVI-0" ) to KScreen::Output(Id: 82 , Name: "DVI-0" ) ( "DVI-0" )
indicitave of an issue such as bad monitor?
3) Can I fix the update issue easily?
4) Are there are fixes i need to do?
Any help/input is appreciated. thanks in advance.