Hi all,
after upgrading to 11.3 I have problems in using the b43 driver. It just disconnects after some period of time (sometimes sooner, sometimes later) with the following messages:
Jul 19 21:55:33 data kernel: 1104.293969] [drm] Num pipes: 1
Jul 19 21:55:49 data kernel: 1120.316042] No probe response from AP 00:15:0c:c6:b9:9b after 500ms, disconnecting.
Jul 19 21:55:49 data kernel: 1120.340128] cfg80211: Calling CRDA to update world regulatory domain
Jul 19 21:55:49 data kernel: 1120.578655] cfg80211: World regulatory domain updated:
Jul 19 21:55:49 data kernel: 1120.578664] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Jul 19 21:55:49 data kernel: 1120.578673] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Jul 19 21:55:49 data kernel: 1120.578681] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
Jul 19 21:55:49 data kernel: 1120.578688] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
Jul 19 21:55:49 data kernel: 1120.578695] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Jul 19 21:55:49 data kernel: 1120.578702] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Jul 19 21:55:50 data kernel: 1121.728137] wlan0: authenticate with 00:15:0c:c6:b9:9b (try 1)
Jul 19 21:55:50 data kernel: 1121.928080] wlan0: authenticate with 00:15:0c:c6:b9:9b (try 2)
Jul 19 21:55:50 data kernel: 1122.128085] wlan0: authenticate with 00:15:0c:c6:b9:9b (try 3)
Jul 19 21:55:51 data kernel: 1122.328081] wlan0: authentication with 00:15:0c:c6:b9:9b timed out
After restarting wpa_supplicant it reassociates again. It is not possible to reassociate using wpa_cli.
Card is 4311 (now working with wl):
05:00.0 Network controller [0280]: Broadcom Corporation BCM4311 802.11b/g WLAN [14e4:4311] (rev 01)
Subsystem: AMBIT Microsystem Corp. Device [1468:0422]
Flags: bus master, fast devsel, latency 0, IRQ 17
Memory at fc300000 (32-bit, non-prefetchable) [size=16]
Capabilities: [40] Power Management version 2
Capabilities: [58] MSI: Enable- Count=1/1 Maskable- 64bit-
Capabilities: [d0] Express Legacy Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [13c] Virtual Channel
Kernel driver in use: wl
I want to go back to b43-module due to ohci_hcd-module-problem (needed to balcklist this one, so that ssb doesn’t get loaded and load it in the end of the boot-sequence. Not a nice hack).
Any advice appreciated!
Thanks and regards,
Martin[/size]