Good day. Newbie here trying to figure out the slow down on my TP Link TL-WN781ND pci-ewireless adapter using latest Tumbleweed. Tried some commands in the terminal via web with the following results:

lspci -k
29:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188EE Wireless Network Adapter (rev 01)
Subsystem: Realtek Semiconductor Co., Ltd. Device 8197
Kernel driver in use: rtl8188ee
Kernel modules: rtl8188ee
dmesg | grep firmware
192:~ # dmesg | grep firmware
[ 2.754007] [drm] Found VCN firmware Version ENC: 1.7 DEC: 4 VEP: 0 Revision: 13
[ 2.754009] [drm] PSP loading VCN firmware
[ 5.810161] rtl8188ee: Using firmware rtlwifi/rtl8188efw.bin
iwconfig wlp41s0
wlp41s0 IEEE 802.11 ESSID:"SweetPotato"
Mode:Managed Frequency:2.462 GHz Access Point: ****************
Bit Rate=135 Mb/s Tx-Power=20 dBm
Retry short limit:7 RTS thr=2347 B Fragment thr 0ff
Encryption key 0ff
Power Management 0ff
Link Quality=48/70 Signal level=-62 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:5142 Missed beacon:0
sudo hwinfo --wlan
[sudo] password for root:
35: PCI 2900.0: 0282 WLAN controller
[Created at pci.386]
Unique ID: ***********************
Parent ID: ***********************
SysFS ID: /devices/pci0000:00/0000:00:01.2/0000:20:00.0/0000:21:07.0/0000:29:00.0
SysFS BusID: 0000:29:00.0
Hardware Class: network
Model: "Realtek RTL8188EE Wireless Network Adapter"
Vendor: pci 0x10ec "Realtek Semiconductor Co., Ltd."
Device: pci 0x8179 "RTL8188EE Wireless Network Adapter"
SubVendor: pci 0x10ec "Realtek Semiconductor Co., Ltd."
SubDevice: pci 0x8197
Revision: 0x01
Driver: "rtl8188ee"
Driver Modules: "rtl8188ee"
Device File: wlp41s0
Features: WLAN
I/O Ports: 0xc000-0xc0ff (rw)
Memory Range: ************************* (rw,non-prefetchable)
IRQ: 142 (no events)
HW Address: ******************
Permanent HW Address: *******************
Link detected: yes
WLAN channels: 1 2 3 4 5 6 7 8 9 10 11
WLAN frequencies: 2.412 2.417 2.422 2.427 2.432 2.437 2.442 2.447 2.452 2.457 2.462
WLAN encryption modes: WEP40 WEP104 TKIP CCMP
WLAN authentication modes: open sharedkey wpa-psk wpa-eap
Module Alias: "*********************************************************"
Driver Info #0:
Driver Status: rtl8188ee is active
Driver Activation Cmd: "modprobe rtl8188ee"
Config Status: cfg=no, avail=yes, need=no, active=unknown
Attached to: #40 (PCI bridge)
via Ookla's Speedtest

**********:~> speedtest-cli
Retrieving configuration...
Testing from *********** (***.***.***.**)...
Retrieving server list...
Selecting best server based on ping...
Hosted by DOST**** (*********) [57.40 km]: 8.241 ms
Testing download speed..................................
Download: 2.67 Mbit/s
Testing upload speed....................................
Upload: 2.01 Mbit/s
See, I manage a higher bandwidth using Windows 10 (in Dual Boot Config | Legacy Setup in Bios), atleast 20Mbps connection (out of 35Mbps in 2.4GHz band) for the same wireless network adapter on the same PC. Distance from AP to PC is about 12 Meters w/ few partitions on the same floor.

Is this a problem within the driver? Link Quality & Signal Level are way too low [Link Quality=48/70 Signal level=-62 dBm]. I'm using a version 3 for Windows driver and here in Tumbleweed uses Version 1 [29:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188EE Wireless Network Adapter (rev 01)]. My ZTE Router | AP has no problems with reliable ISP to date, btw.

I hope someone could lead me to a right troubleshooting tips. TIA