Results 1 to 9 of 9

Thread: GOpenVPN ?

  1. #1

    Default GOpenVPN ?

    Do we have a package for this application GOpenVPN?

    I try to compile it from source and after spending some time I could not complete it due to many errors, I believe I had all dependencies.
    I was wondering if there is an rpm for this application.

  2. #2
    Join Date
    May 2012
    Location
    Finland
    Posts
    2,005

    Default Re: GOpenVPN ?

    Is there a specific need for this as NetworkManager for GNOME supports OpenVPN ( NetworkManager-openvpn-gnome )?
    .: miuku #suse @ irc.freenode.net
    :: miuku@opensuse.org

    .: h​ttps://download.opensuse.org/repositories/home:/Miuku/

  3. #3

    Default Re: GOpenVPN ?

    Quote Originally Posted by Miuku View Post
    Is there a specific need for this as NetworkManager for GNOME supports OpenVPN ( NetworkManager-openvpn-gnome )?
    For my use wicked works better than the new NM. I know the following belong to another topic but for my use, I like to have DHCP running and add a fix IP to the node. I could do it with the NM of 13.1 but not with the one from 13.2. For example if I run the 13.2 NM under DHCP and run ip addr you will see the assigned ip, now if you add an extra ip ( ip address add 192.168.0.64 dev eth0) for example then run ip addr you will see now the 2 ip's associated with the same net card. This is temporary and i can not find a way to do it under the NM to make it permanent like under 13.1. Of course I can do it with the wicked, that is the reason I try to find a GUI for openvpn which now I have to do it with the CLI

  4. #4
    Join Date
    Jun 2008
    Location
    Podunk
    Posts
    27,194
    Blog Entries
    15

    Default Re: GOpenVPN ?

    On Wed 03 Dec 2014 02:06:01 PM CST, tdecampo wrote:


    Miuku;2680443 Wrote:
    > Is there a specific need for this as NetworkManager for GNOME supports
    > OpenVPN ( NetworkManager-openvpn-gnome )?


    For my use wicked works better than the new NM. I know the following
    belong to another topic but for my use, I like to have DHCP running and
    add a fix IP to the node. I could do it with the NM of 13.1 but not with
    the one from 13.2. For example if I run the 13.2 NM under DHCP and run
    ip addr you will see the assigned ip, now if you add an extra ip ( ip
    address add 192.168.0.64 dev eth0) for example then run ip addr you will
    see now the 2 ip's associated with the same net card. This is temporary
    and i can not find a way to do it under the NM to make it permanent like
    under 13.1. Of course I can do it with the wicked, that is the reason I
    try to find a GUI for openvpn which now I have to do it with the CLI


    Hi
    So just to clarify, you could do what you want in the 13.1 NM (maybe
    some details of where in NM), but not in NM with 13.2?

    It might be something that was removed (a regression...)?

    --
    Cheers Malcolm °¿° LFCS, SUSE Knowledge Partner (Linux Counter #276890)
    SUSE Linux Enterprise Desktop 12 GNOME 3.10.1 Kernel 3.12.28-4-default
    If you find this post helpful and are logged into the web interface,
    please show your appreciation and click on the star below... Thanks!


  5. #5

    Default Re: GOpenVPN ?

    Quote Originally Posted by malcolmlewis View Post
    Hi
    So just to clarify, you could do what you want in the 13.1 NM (maybe
    some details of where in NM), but not in NM with 13.2?

    It might be something that was removed (a regression...)?
    Malcolm,

    Thxs. I was going to post 2 pictures of the NM from 13.1 to explain what I meant but.. I am not allowed to post attachments ;-(

    Basically in the NM 0.9.8.8-10.1 in OS 13.2 the IPv4 page
    shows under Method: DHCP and then there is a drop down menu (basic setting - additional addresses..etc)
    Under additional addresses you can add your fix IP.

    Here is the result after doing it:

    -------------
    tdec@linux-gfn4:~> ip addr
    1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
    valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host
    valid_lft forever preferred_lft forever
    2: eno1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
    link/ether bc:ae:c5:77:ef:5f brd ff:ff:ff:ff:ff:ff
    inet 10.0.0.34/24 brd 10.0.0.255 scope global eno1
    valid_lft forever preferred_lft forever
    inet 10.0.0.64/24 brd 10.0.0.255 scope global secondary eno1
    valid_lft forever preferred_lft forever
    inet6 2601:1:ae00:f0d:beae:c5ff:fe77:ef5f/64 scope global dynamic
    valid_lft 322373sec preferred_lft 322373sec
    inet6 fe80::beae:c5ff:fe77:ef5f/64 scope link
    valid_lft forever preferred_lft forever
    -----------------------------------------
    Where you can see both the
    10.0.0.34 provided by dhcp
    10.0.0.64 that is the fix IP I added.

    The new NM does not allow (afaik) to have the dhcp and ip added addresses is basically dhcp or fix ip

    Yes I can have the NW provide the address by the dhcp and then I can add the fix ip using ip command but is only temporary, after reboot you are back to the NM only. Having both done by the NM like under 13.1 is permanent.

  6. #6
    Join Date
    Jun 2008
    Location
    Podunk
    Posts
    27,194
    Blog Entries
    15

    Default Re: GOpenVPN ?

    Hi
    If you could post the images here;

    http://paste.opensuse.org/

    PS, set to never expire
    Cheers Malcolm °¿° SUSE Knowledge Partner (Linux Counter #276890)
    SUSE SLE, openSUSE Leap/Tumbleweed (x86_64) | GNOME DE
    If you find this post helpful and are logged into the web interface,
    please show your appreciation and click on the star below... Thanks!

  7. #7

    Default Re: GOpenVPN ?

    http://paste.opensuse.org/33728683
    http://paste.opensuse.org/22494970

    These are the 2 images of the NetworkManger in openSuSE 13.1 (0.9.8.8-10.1-x86_64) that show how to add a second ip to the one provided by the DHCP

    -=terry=-
    Last edited by tdecampo; 03-Dec-2014 at 15:04. Reason: unable to see the images

  8. #8
    Join Date
    Jun 2008
    Location
    Podunk
    Posts
    27,194
    Blog Entries
    15

    Default Re: GOpenVPN ?

    Hi

    Ahhh this is KDE.... my bad I thought you were using GNOME NM.... (since you were looking at a GTK 2 app...)
    Cheers Malcolm °¿° SUSE Knowledge Partner (Linux Counter #276890)
    SUSE SLE, openSUSE Leap/Tumbleweed (x86_64) | GNOME DE
    If you find this post helpful and are logged into the web interface,
    please show your appreciation and click on the star below... Thanks!

  9. #9

    Default Re: GOpenVPN ?

    Quote Originally Posted by malcolmlewis View Post
    Hi

    Ahhh this is KDE.... my bad I thought you were using GNOME NM.... (since you were looking at a GTK 2 app...)
    Malcolm,

    I just installed openSuSE13,.2 gnome in a VM session to look at the NetworkManager gnome applet. Basically is the same as the plasmoid in KDE with the same functionality and the same constrains. It does not allow me to add a fix Ip on the top of DHCP.
    The good news is that the devs are trying to add openvpn functionality to wicked. I will keep trying to compile gopenvpn until the.
    Thanks
    -=terry=-

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •