Results 1 to 3 of 3

Thread: k3b burning trouble -- 12.3

  1. #1

    Post k3b burning trouble -- 12.3

    Hey there. Newby here.

    recently switched to 12.3 xfce. trying to install burning tool. trouble with brasero, so i choose k3b which worked out fin over the years. but every time I try to burn, it ejects the cd while sending cue-sheet.

    System
    -----------------------
    K3b Version: 1.0.5

    KDE Version: 3.5.10 "release 262"
    QT Version: 3.3.8c
    Kernel: 3.7.10-1.28-default
    Devices
    -----------------------
    SAMSUNG CDRW/DVD SN-324F U203 (/dev/sr0, /dev/sg1) [CD-R, CD-RW, CD-ROM, DVD-ROM] [DVD-ROM, CD-ROM, CD-R, CD-RW] [SAO, TAO, RAW, SAO/R96P, SAO/R96R, RAW/R16, RAW/R96P, RAW/R96R]

    Used versions
    -----------------------
    cdrecord: 1.1.11

    cdrecord
    -----------------------
    /usr/bin/X11/wodim: Operation not permitted. Warning: Cannot raise RLIMIT_MEMLOCK limits.
    scsidev: '/dev/sr0'
    devname: '/dev/sr0'
    scsibus: -2 target: -2 lun: -2
    Linux sg driver version: 3.5.27
    Wodim version: 1.1.11
    SCSI buffer size: 64512
    Beginning DMA speed test. Set CDR_NODMATEST environment variable if device
    communication breaks or freezes immediately after that.
    Text len: 162
    TOC Type: 0 = CD-DA
    Driveropts: 'burnfree'
    Device type : Removable CD-ROM
    Version : 5
    Response Format: 2
    Capabilities :
    Vendor_info : 'SAMSUNG '
    Identification : 'CDRW/DVD SN-324F'
    Revision : 'U203'
    Device seems to be: Generic mmc2 DVD-ROM.
    Current: 0x0009 (CD-R)
    Profile: 0x000A (CD-RW)
    Profile: 0x0009 (CD-R) (current)
    Profile: 0x0008 (CD-ROM)
    Profile: 0x0010 (DVD-ROM)
    Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
    Driver flags : MMC-3 SWABAUDIO BURNFREE
    Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R
    Drive buf size : 1959936 = 1914 KB
    FIFO size : 12582912 = 12288 KB
    pregap1: -1
    Track 01: audio 516 MB (51:09.97) no preemp swab copy
    Total size: 516 MB (51:09.97) = 230248 sectors
    Lout start: 516 MB (51:11/73) = 230248 sectors
    Current Secsize: 2048
    ATIP info from disk:
    Indicated writing power: 5
    Is not unrestricted
    Is not erasable
    Disk sub type: Medium Type A, high Beta category (A+) (3)
    ATIP start of lead in: -11634 (97:26/66)
    ATIP start of lead out: 359846 (79:59/71)
    Disk type: Short strategy type (Phthalocyanine or similar)
    Manuf. index: 3
    Manufacturer: CMC Magnetics Corporation
    Blocks total: 359846 Blocks current: 359846 Blocks remaining: 129598
    Starting to write CD/DVD at speed 24.0 in real SAO mode for single session.
    Last chance to quit, starting real write in 2 seconds.
    Speed set to 4226 KB/s
    1 seconds.
    0 seconds. Operation starts.
    Waiting for reader process to fill input buffer ... input buffer ready.
    Performing OPC...
    Sending CUE sheet...
    Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error
    CDB: 2A 00 FF FF D5 28 00 02 9A 00
    status: 0x2 (CHECK CONDITION)
    Sense Bytes: F1 00 03 00 00 00 00 0A 00 00 00 00 0C 00 00 00
    Sense Key: 0x3 Medium Error, deferred error, Segment 0
    Sense Code: 0x0C Qual 0x00 (write error) Fru 0x0
    Sense flags: Blk 0 (valid)
    cmd finished after 3.765s timeout 200s
    /usr/bin/X11/wodim: Could not write Lead-in.
    SAO startsec: -11634
    Writing lead-in...
    write CD-Text data: error after 63936 bytes
    Writing time: 29.091s
    BURN-Free was never needed.
    /usr/bin/X11/wodim: fifo had 192 puts and 0 gets.
    /usr/bin/X11/wodim: fifo was 0 times empty and 0 times full, min fill was 100%.

    cdrecord command:
    -----------------------
    /usr/bin/X11/wodim -v gracetime=2 dev=/dev/sr0 speed=24 -dao driveropts=burnfree textfile=/tmp/k3bSECaMw.dat -eject -useinfo -audio /tmp/kde-captain/k3b_audio_1_01.inf
    could someone PLEASE tell me whats the problem?

    thanx in advance

  2. #2
    Join Date
    Jun 2008
    Location
    Moses Lake, WA. USA
    Posts
    474

    Default Re: k3b burning trouble -- 12.3

    franz gans wrote:

    >
    > Hey there. Newby here.
    >
    > recently switched to 12.3 xfce. trying to install burning tool.
    > trouble with brasero, so i choose k3b which worked out fin over the
    > years. but every time I try to burn, it ejects the cd while sending
    > cue-sheet.
    >
    >> System
    >> -----------------------
    >> K3b Version: 1.0.5
    >>
    >> KDE Version: 3.5.10 "release 262"
    >> QT Version: 3.3.8c
    >> Kernel: 3.7.10-1.28-default
    >> Devices
    >> -----------------------
    >> SAMSUNG CDRW/DVD SN-324F U203 (/dev/sr0, /dev/sg1) [CD-R, CD-RW,
    >> CD-ROM, DVD-ROM] [DVD-ROM, CD-ROM, CD-R, CD-RW] [SAO, TAO, RAW,
    >> SAO/R96P, SAO/R96R, RAW/R16, RAW/R96P, RAW/R96R]
    >>
    >> Used versions
    >> -----------------------
    >> cdrecord: 1.1.11
    >>
    >> cdrecord
    >> -----------------------
    >> /usr/bin/X11/wodim: Operation not permitted. Warning: Cannot raise
    >> RLIMIT_MEMLOCK limits.
    >> scsidev: '/dev/sr0'
    >> devname: '/dev/sr0'
    >> scsibus: -2 target: -2 lun: -2
    >> Linux sg driver version: 3.5.27
    >> Wodim version: 1.1.11
    >> SCSI buffer size: 64512
    >> Beginning DMA speed test. Set CDR_NODMATEST environment variable if
    >> device
    >> communication breaks or freezes immediately after that.
    >> Text len: 162
    >> TOC Type: 0 = CD-DA
    >> Driveropts: 'burnfree'
    >> Device type : Removable CD-ROM
    >> Version : 5
    >> Response Format: 2
    >> Capabilities :
    >> Vendor_info : 'SAMSUNG '
    >> Identification : 'CDRW/DVD SN-324F'
    >> Revision : 'U203'
    >> Device seems to be: Generic mmc2 DVD-ROM.
    >> Current: 0x0009 (CD-R)
    >> Profile: 0x000A (CD-RW)
    >> Profile: 0x0009 (CD-R) (current)
    >> Profile: 0x0008 (CD-ROM)
    >> Profile: 0x0010 (DVD-ROM)
    >> Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
    >> Driver flags : MMC-3 SWABAUDIO BURNFREE
    >> Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P
    >> RAW/R96R
    >> Drive buf size : 1959936 = 1914 KB
    >> FIFO size : 12582912 = 12288 KB
    >> pregap1: -1
    >> Track 01: audio 516 MB (51:09.97) no preemp swab copy
    >> Total size: 516 MB (51:09.97) = 230248 sectors
    >> Lout start: 516 MB (51:11/73) = 230248 sectors
    >> Current Secsize: 2048
    >> ATIP info from disk:
    >> Indicated writing power: 5
    >> Is not unrestricted
    >> Is not erasable
    >> Disk sub type: Medium Type A, high Beta category (A+) (3)
    >> ATIP start of lead in: -11634 (97:26/66)
    >> ATIP start of lead out: 359846 (79:59/71)
    >> Disk type: Short strategy type (Phthalocyanine or similar)
    >> Manuf. index: 3
    >> Manufacturer: CMC Magnetics Corporation
    >> Blocks total: 359846 Blocks current: 359846 Blocks remaining:

    129598
    >> Starting to write CD/DVD at speed 24.0 in real SAO mode for single
    >> session.
    >> Last chance to quit, starting real write in 2 seconds.
    >> Speed set to 4226 KB/s
    >> 1 seconds.
    >> 0 seconds. Operation starts.
    >> Waiting for reader process to fill input buffer ... input buffer
    >> ready. Performing OPC...
    >> Sending CUE sheet...
    >> Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error
    >> CDB: 2A 00 FF FF D5 28 00 02 9A 00
    >> status: 0x2 (CHECK CONDITION)
    >> Sense Bytes: F1 00 03 00 00 00 00 0A 00 00 00 00 0C 00 00 00
    >> Sense Key: 0x3 Medium Error, deferred error, Segment 0
    >> Sense Code: 0x0C Qual 0x00 (write error) Fru 0x0
    >> Sense flags: Blk 0 (valid)
    >> cmd finished after 3.765s timeout 200s
    >> /usr/bin/X11/wodim: Could not write Lead-in.
    >> SAO startsec: -11634
    >> Writing lead-in...
    >> write CD-Text data: error after 63936 bytes
    >> Writing time: 29.091s
    >> BURN-Free was never needed.
    >> /usr/bin/X11/wodim: fifo had 192 puts and 0 gets.
    >> /usr/bin/X11/wodim: fifo was 0 times empty and 0 times full, min

    fill
    >> was 100%.
    >>
    >> cdrecord command:
    >> -----------------------
    >> /usr/bin/X11/wodim -v gracetime=2 dev=/dev/sr0 speed=24 -dao
    >> driveropts=burnfree textfile=/tmp/k3bSECaMw.dat -eject -useinfo
    >> -audio /tmp/kde-captain/k3b_audio_1_01.inf
    >>
    >>

    >
    > could someone PLEASE tell me whats the problem?
    >
    > thanx in advance

    Have you tried the latest version of k3b? On openSUSE 13.1 it is 2.02.
    Don't know if it will help. i also use that version on 12.3. But I run
    under KDE.

    Russ
    >

    --
    openSUSE 13.1(Linux 3.11.10-7-desktop x86_64|
    Intel(R) Quad Core(TM) i5-4440 CPU @ 3.10GHz|8GB DDR3|
    GeForce 8400GS (NVIDIA-Linux-x86_64-331.49)|KDE 4.12.4


  3. #3
    Join Date
    Oct 2008
    Location
    Glasgow, Scotland
    Posts
    1,131

    Default Re: k3b burning trouble -- 12.3

    Quote Originally Posted by franz_gans View Post
    Hey there. Newby here.

    recently switched to 12.3 xfce. trying to install burning tool. trouble with brasero, so i choose k3b which worked out fin over the years. but every time I try to burn, it ejects the cd while sending cue-sheet.
    Well the best K3b/KDE versions available in the openSUSE-12.3 oss repository are 2.0.2/4.10.0. For a very lightweight, fast desktop I prefer Openbox, which I think runs KDE applications better than Xfce, which I find more Gnome-centric. K3b-2.0.2 definately works well from Openbox.
    ~Thank you for sharing an interesting problem.
    --
    slàinte mhath,
    rayH

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •