Page 1 of 3 123 LastLast
Results 1 to 10 of 21

Thread: USB 3.0 support in 13.1 KDE (Revisited)

  1. #1

    Default USB 3.0 support in 13.1 KDE (Revisited)

    My USB 3.0 external hard drive is not recognized when plugged into a USB 2.0 slot on my box. I remember seeing somewhere that the device should be negotiated down to 2.0 speed but mine is not even seen by the opsys. Am I not remembering correctly or is my machine not configured correctly? Thanks!

  2. #2
    Join Date
    Jun 2008
    Location
    Auckland, NZ
    Posts
    23,708
    Blog Entries
    1

    Default Re: USB 3.0 support in 13.1 KDE (Revisited)

    Quote Originally Posted by chuckenheimer View Post
    My USB 3.0 external hard drive is not recognized when plugged into a USB 2.0 slot on my box. I remember seeing somewhere that the device should be negotiated down to 2.0 speed but mine is not even seen by the opsys. Am I not remembering correctly or is my machine not configured correctly? Thanks!
    Hard to say without any real info provided. Open a terminal and run
    Code:
    sudo tail -f /var/log/messages
    Plug in the USB 3 HDD and observe/post what is reported. Maybe someone will be able to advise further.

    It might also be useful to report output
    Code:
    usb-devices
    *If this command is not available, install the 'usbutils' package.

  3. #3
    Join Date
    Jun 2008
    Location
    Auckland, NZ
    Posts
    23,708
    Blog Entries
    1

    Default Re: USB 3.0 support in 13.1 KDE (Revisited)

    Another possibility is that the USB 2 port may not provide enough power to start the USB 3 HDD. A USB powered hub might help if this is the case, or perhaps the HDD can be powered via an external PSU?

  4. #4

    Default Re: USB 3.0 support in 13.1 KDE (Revisited)

    Quote Originally Posted by deano_ferrari View Post
    Hard to say without any real info provided. Open a terminal and run
    Code:
    sudo tail -f /var/log/messages
    Plug in the USB 3 HDD and observe/post what is reported. Maybe someone will be able to advise further.

    It might also be useful to report output
    Code:
    usb-devices
    *If this command is not available, install the 'usbutils' package.
    Code:
    linux-uc1g:/home/charles # sudo tail -f /var/log/messages
    2014-01-06T02:30:01.718891-06:00 linux-uc1g systemd[1]: Started Session 23 of user root.
    2014-01-06T02:30:01.989631-06:00 linux-uc1g /USR/SBIN/CRON[2843]: pam_unix(crond:session): session closed for user root
    2014-01-06T02:43:06.831092-06:00 linux-uc1g sudo: pam_unix(sudo:auth): authentication failure; logname=charles uid=1000 euid=0 tty=/dev/pts/1 ruser=charles rhost=  user=root
    2014-01-06T02:44:06.308040-06:00 linux-uc1g sudo:  charles : 3 incorrect password attempts ; TTY=pts/1 ; PWD=/home/charles ; USER=root ; COMMAND=/usr/bin/tail -f /var/log/messages
    2014-01-06T02:44:42.820478-06:00 linux-uc1g su: (to charles) charles on none
    2014-01-06T02:44:42.823415-06:00 linux-uc1g su: pam_unix(su:session): session opened for user root by charles(uid=1000)
    2014-01-06T02:44:42.830355-06:00 linux-uc1g su: pam_systemd(su:session): pam_putenv: delete non-existent entry; XDG_RUNTIME_DIR
    2014-01-06T02:45:00.128701-06:00 linux-uc1g sudo:     root : TTY=pts/1 ; PWD=/home/charles ; USER=root ; COMMAND=/usr/bin/tail -f /var/log/messages
    2014-01-06T02:45:00.135056-06:00 linux-uc1g sudo: pam_unix(sudo:session): session opened for user root by charles(uid=0)
    2014-01-06T02:45:00.142440-06:00 linux-uc1g sudo: pam_systemd(sudo:session): pam_putenv: delete non-existent entry; XDG_RUNTIME_DIR
    2014-01-06T02:45:01.011007-06:00 linux-uc1g /usr/sbin/cron[2983]: pam_unix(crond:session): session opened for user root by (uid=0)
    2014-01-06T02:45:01.019842-06:00 linux-uc1g systemd[1]: Starting Session 24 of user root.
    2014-01-06T02:45:01.023997-06:00 linux-uc1g systemd[1]: Started Session 24 of user root.
    2014-01-06T02:45:01.189612-06:00 linux-uc1g /USR/SBIN/CRON[2983]: pam_unix(crond:session): session closed for user root
    2014-01-06T02:45:24.160996-06:00 linux-uc1g kernel: [20436.652043] usb 10-1: new full-speed USB device number 2 using ohci-pci
    2014-01-06T02:45:24.325991-06:00 linux-uc1g kernel: [20436.817061] usb 10-1: device descriptor read/64, error -62
    2014-01-06T02:45:24.591988-06:00 linux-uc1g kernel: [20437.083052] usb 10-1: device descriptor read/64, error -62
    2014-01-06T02:45:24.849990-06:00 linux-uc1g kernel: [20437.341052] usb 10-1: new full-speed USB device number 3 using ohci-pci
    2014-01-06T02:45:25.014986-06:00 linux-uc1g kernel: [20437.506046] usb 10-1: device descriptor read/64, error -62
    2014-01-06T02:45:25.280990-06:00 linux-uc1g kernel: [20437.772063] usb 10-1: device descriptor read/64, error -62
    2014-01-06T02:45:25.538991-06:00 linux-uc1g kernel: [20438.030059] usb 10-1: new full-speed USB device number 4 using ohci-pci
    2014-01-06T02:45:25.942993-06:00 linux-uc1g kernel: [20438.434046] usb 10-1: device not accepting address 4, error -62
    2014-01-06T02:45:26.099987-06:00 linux-uc1g kernel: [20438.591052] usb 10-1: new full-speed USB device number 5 using ohci-pci
    2014-01-06T02:45:26.503992-06:00 linux-uc1g kernel: [20438.995045] usb 10-1: device not accepting address 5, error -62
    2014-01-06T02:45:26.504024-06:00 linux-uc1g kernel: [20438.995072] hub 10-0:1.0: unable to enumerate USB device on port 1                                   
    ^Clinux-uc1g:/home/charles #
    Code:
    Clinux-uc1g:/home/charles # usb-devices                                                                                                                    
                                                                                                                                                                
    T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480 MxCh= 5                                                                                           
    D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1                                                                                                
    P:  Vendor=1d6b ProdID=0002 Rev=03.11                                                                                                                       
    S:  Manufacturer=Linux 3.11.10-7.g016ba65-desktop ehci_hcd                                                                                                  
    S:  Product=EHCI Host Controller
    S:  SerialNumber=0000:00:0a.2
    C:  #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
    I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
    
    T:  Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#=  2 Spd=480 MxCh= 0
    D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
    P:  Vendor=0930 ProdID=6545 Rev=01.00
    S:  Manufacturer=        
    S:  Product=USB Flash Memory
    S:  SerialNumber=6C626DBED99FED80E0009E1C
    C:  #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=200mA
    I:  If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
    
    T:  Bus=10 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 2
    D:  Ver= 1.10 Cls=09(hub  ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
    P:  Vendor=1d6b ProdID=0001 Rev=03.11
    S:  Manufacturer=Linux 3.11.10-7.g016ba65-desktop ohci_hcd
    S:  Product=OHCI PCI host controller
    S:  SerialNumber=0000:02:01.1
    C:  #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
    I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
    
    T:  Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480 MxCh= 6
    D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
    P:  Vendor=1d6b ProdID=0002 Rev=03.11
    S:  Manufacturer=Linux 3.11.10-7.g016ba65-desktop ehci_hcd
    S:  Product=EHCI Host Controller
    S:  SerialNumber=0000:00:10.3
    C:  #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
    I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
    
    T:  Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480 MxCh= 5
    D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
    P:  Vendor=1d6b ProdID=0002 Rev=03.11
    S:  Manufacturer=Linux 3.11.10-7.g016ba65-desktop ehci_hcd
    S:  Product=EHCI Host Controller
    S:  SerialNumber=0000:02:01.2
    C:  #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
    I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
    
    T:  Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#=  2 Spd=480 MxCh= 0
    D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
    P:  Vendor=13fe ProdID=1e00 Rev=01.10
    S:  Manufacturer=        
    S:  Product=Patriot Memory
    S:  SerialNumber=079917018D3108EC
    C:  #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=200mA
    I:  If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
    
    T:  Bus=04 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 2
    D:  Ver= 1.10 Cls=09(hub  ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
    P:  Vendor=1d6b ProdID=0001 Rev=03.11
    S:  Manufacturer=Linux 3.11.10-7.g016ba65-desktop uhci_hcd
    S:  Product=UHCI Host Controller
    S:  SerialNumber=0000:00:10.0
    C:  #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
    I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
    
    T:  Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  2 Spd=1.5 MxCh= 0
    D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
    P:  Vendor=1241 ProdID=f761 Rev=02.20
    S:  Manufacturer=HOLTEK
    S:  Product=Wireless Keyboard/Mouse(2.4G)
    C:  #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr=100mA
    I:  If#= 0 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=01 Prot=01 Driver=usbhid
    I:  If#= 1 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=01 Prot=02 Driver=usbhid
    
    T:  Bus=05 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 2
    D:  Ver= 1.10 Cls=09(hub  ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
    P:  Vendor=1d6b ProdID=0001 Rev=03.11
    S:  Manufacturer=Linux 3.11.10-7.g016ba65-desktop uhci_hcd
    S:  Product=UHCI Host Controller
    S:  SerialNumber=0000:00:10.1
    C:  #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
    I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
    
    T:  Bus=06 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 2
    D:  Ver= 1.10 Cls=09(hub  ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
    P:  Vendor=1d6b ProdID=0001 Rev=03.11
    S:  Manufacturer=Linux 3.11.10-7.g016ba65-desktop uhci_hcd
    S:  Product=UHCI Host Controller
    S:  SerialNumber=0000:00:10.2
    C:  #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
    I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
    
    T:  Bus=07 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 3
    D:  Ver= 1.10 Cls=09(hub  ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
    P:  Vendor=1d6b ProdID=0001 Rev=03.11
    S:  Manufacturer=Linux 3.11.10-7.g016ba65-desktop ohci_hcd
    S:  Product=OHCI PCI host controller
    S:  SerialNumber=0000:00:0a.0
    C:  #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
    I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
    
    T:  Bus=08 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 2
    D:  Ver= 1.10 Cls=09(hub  ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
    P:  Vendor=1d6b ProdID=0001 Rev=03.11
    S:  Manufacturer=Linux 3.11.10-7.g016ba65-desktop ohci_hcd
    S:  Product=OHCI PCI host controller
    S:  SerialNumber=0000:00:0a.1
    C:  #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
    I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
    
    T:  Bus=09 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 3
    D:  Ver= 1.10 Cls=09(hub  ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
    P:  Vendor=1d6b ProdID=0001 Rev=03.11
    S:  Manufacturer=Linux 3.11.10-7.g016ba65-desktop ohci_hcd
    S:  Product=OHCI PCI host controller
    S:  SerialNumber=0000:02:01.0
    C:  #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
    I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
    linux-uc1g:/home/charles #
    Also, I will try the powered USB hub and see if that affects things. Thanks.

  5. #5

    Default Re: USB 3.0 support in 13.1 KDE (Revisited)

    The powered hub made no difference, so I presume there is enough power from those ports on my desktop machine. This is the machine I am trying to get the external device recognized on.

  6. #6
    Join Date
    Jun 2008
    Location
    Auckland, NZ
    Posts
    23,708
    Blog Entries
    1

    Default Re: USB 3.0 support in 13.1 KDE (Revisited)

    Code:
    2014-01-06T02:45:24.325991-06:00 linux-uc1g kernel: [20436.817061] usb 10-1: device descriptor read/64, error -62
    2014-01-06T02:45:24.591988-06:00 linux-uc1g kernel: [20437.083052] usb 10-1: device descriptor read/64, error -62
    2014-01-06T02:45:24.849990-06:00 linux-uc1g kernel: [20437.341052] usb 10-1: new full-speed USB device number 3 using ohci-pci
    2014-01-06T02:45:25.014986-06:00 linux-uc1g kernel: [20437.506046] usb 10-1: device descriptor read/64, error -62
    2014-01-06T02:45:25.280990-06:00 linux-uc1g kernel: [20437.772063] usb 10-1: device descriptor read/64, error -62
    2014-01-06T02:45:25.538991-06:00 linux-uc1g kernel: [20438.030059] usb 10-1: new full-speed USB device number 4 using ohci-pci
    2014-01-06T02:45:25.942993-06:00 linux-uc1g kernel: [20438.434046] usb 10-1: device not accepting address 4, error -62
    2014-01-06T02:45:26.099987-06:00 linux-uc1g kernel: [20438.591052] usb 10-1: new full-speed USB device number 5 using ohci-pci
    2014-01-06T02:45:26.503992-06:00 linux-uc1g kernel: [20438.995045] usb 10-1: device not accepting address 5, error -62
    2014-01-06T02:45:26.504024-06:00 linux-uc1g kernel: [20438.995072] hub 10-0:1.0: unable to enumerate USB device on port 1
    The errors reported could well be symptomatic of a power consumption issue. I've read of this behaviour elsewhere eg

    How to fix "device not accepting address" error | Paul Philippov

  7. #7
    Join Date
    Jun 2008
    Location
    Auckland, NZ
    Posts
    23,708
    Blog Entries
    1

    Default Re: USB 3.0 support in 13.1 KDE (Revisited)

    Quote Originally Posted by chuckenheimer View Post
    The powered hub made no difference, so I presume there is enough power from those ports on my desktop machine. This is the machine I am trying to get the external device recognized on.
    1. Are you getting the same kind of errors with the powered hub in the line?

    2. Do you have a USB 3 port to compare behaviour with?

  8. #8

    Default Re: USB 3.0 support in 13.1 KDE (Revisited)

    Quote Originally Posted by deano_ferrari View Post
    1. Are you getting the same kind of errors with the powered hub in the line?

    2. Do you have a USB 3 port to compare behaviour with?
    ++++++++++++++++++++++++++++++++++++++++++++++++++++++++

    Just wanted to say that I found an application at https://01.org/powertop/ that comes in a tarball but I don't know how to utilize it. I know nothing about using these types of applications on Linux but did notice an Install script (I recognized that much in the archive) and presume that might be the way to install the program but don't know enough how to go about doing that. This is supposed to monitor USB port power consumption with which I might be able to see if that is indeed the problem.

    1. I will obtain this information for a later post.

    2. No, there is no USB 3 PCI card to test. Maybe in the future when I bring up another of my older boxes with a new OpenSUSE 13.1 installation that I am planning on later.

    Thanks for the continued support and, FYI, I read the previous post in which this was discussed here on the forums. Very complex and above my head though.

  9. #9

    Default Re: USB 3.0 support in 13.1 KDE (Revisited)

    Quote Originally Posted by deano_ferrari View Post
    Code:
    2014-01-06T02:45:24.325991-06:00 linux-uc1g kernel: [20436.817061] usb 10-1: device descriptor read/64, error -62
    2014-01-06T02:45:24.591988-06:00 linux-uc1g kernel: [20437.083052] usb 10-1: device descriptor read/64, error -62
    2014-01-06T02:45:24.849990-06:00 linux-uc1g kernel: [20437.341052] usb 10-1: new full-speed USB device number 3 using ohci-pci
    2014-01-06T02:45:25.014986-06:00 linux-uc1g kernel: [20437.506046] usb 10-1: device descriptor read/64, error -62
    2014-01-06T02:45:25.280990-06:00 linux-uc1g kernel: [20437.772063] usb 10-1: device descriptor read/64, error -62
    2014-01-06T02:45:25.538991-06:00 linux-uc1g kernel: [20438.030059] usb 10-1: new full-speed USB device number 4 using ohci-pci
    2014-01-06T02:45:25.942993-06:00 linux-uc1g kernel: [20438.434046] usb 10-1: device not accepting address 4, error -62
    2014-01-06T02:45:26.099987-06:00 linux-uc1g kernel: [20438.591052] usb 10-1: new full-speed USB device number 5 using ohci-pci
    2014-01-06T02:45:26.503992-06:00 linux-uc1g kernel: [20438.995045] usb 10-1: device not accepting address 5, error -62
    2014-01-06T02:45:26.504024-06:00 linux-uc1g kernel: [20438.995072] hub 10-0:1.0: unable to enumerate USB device on port 1
    The errors reported could well be symptomatic of a power consumption issue. I've read of this behaviour elsewhere eg

    How to fix "device not accepting address" error | Paul Philippov
    ++++++++++++++++++++++++++++++++++++++++++++++++++

    This remedy was unfruitful. FYI, I have two different manufacturers PCI cards in my box and neither of them wants to recognize the external hard drive.

  10. #10

    Default Re: USB 3.0 support in 13.1 KDE (Revisited)

    Hmm. Different result this time with the powered hub:

    Code:
    charles@linux-uc1g:~> sudo tail -f /var/log/messages
    root's password:
    2014-01-06T05:07:28.243873-06:00 linux-uc1g kernel: [ 5761.038050] usb 8-1: device descriptor read/64, error -62
    2014-01-06T05:07:28.509862-06:00 linux-uc1g kernel: [ 5761.304045] usb 8-1: device descriptor read/64, error -62
    2014-01-06T05:07:28.767871-06:00 linux-uc1g kernel: [ 5761.562051] usb 8-1: new full-speed USB device number 10 using ohci-pci
    2014-01-06T05:07:29.171871-06:00 linux-uc1g kernel: [ 5761.966055] usb 8-1: device not accepting address 10, error -62
    2014-01-06T05:07:29.328869-06:00 linux-uc1g kernel: [ 5762.123075] usb 8-1: new full-speed USB device number 11 using ohci-pci
    2014-01-06T05:07:29.732868-06:00 linux-uc1g kernel: [ 5762.527051] usb 8-1: device not accepting address 11, error -62
    2014-01-06T05:07:29.732900-06:00 linux-uc1g kernel: [ 5762.527084] hub 8-0:1.0: unable to enumerate USB device on port 1
    2014-01-06T05:08:09.349616-06:00 linux-uc1g sudo:  charles : TTY=pts/2 ; PWD=/home/charles ; USER=root ; COMMAND=/usr/bin/tail -f /var/log/messages
    2014-01-06T05:08:09.351973-06:00 linux-uc1g sudo: pam_unix(sudo:session): session opened for user root by charles(uid=0)
    2014-01-06T05:08:09.358012-06:00 linux-uc1g sudo: pam_systemd(sudo:session): pam_putenv: delete non-existent entry; XDG_RUNTIME_DIR
    ^Ccharles@linux-uc1g:~> sudo tail -f /var/log/messages
    2014-01-06T05:07:29.328869-06:00 linux-uc1g kernel: [ 5762.123075] usb 8-1: new full-speed USB device number 11 using ohci-pci
    2014-01-06T05:07:29.732868-06:00 linux-uc1g kernel: [ 5762.527051] usb 8-1: device not accepting address 11, error -62
    2014-01-06T05:07:29.732900-06:00 linux-uc1g kernel: [ 5762.527084] hub 8-0:1.0: unable to enumerate USB device on port 1
    2014-01-06T05:08:09.349616-06:00 linux-uc1g sudo:  charles : TTY=pts/2 ; PWD=/home/charles ; USER=root ; COMMAND=/usr/bin/tail -f /var/log/messages
    2014-01-06T05:08:09.351973-06:00 linux-uc1g sudo: pam_unix(sudo:session): session opened for user root by charles(uid=0)
    2014-01-06T05:08:09.358012-06:00 linux-uc1g sudo: pam_systemd(sudo:session): pam_putenv: delete non-existent entry; XDG_RUNTIME_DIR
    2014-01-06T05:09:08.273904-06:00 linux-uc1g sudo: pam_unix(sudo:session): session closed for user root
    2014-01-06T05:09:15.790317-06:00 linux-uc1g sudo:  charles : TTY=pts/2 ; PWD=/home/charles ; USER=root ; COMMAND=/usr/bin/tail -f /var/log/messages
    2014-01-06T05:09:15.792554-06:00 linux-uc1g sudo: pam_unix(sudo:session): session opened for user root by charles(uid=0)
    2014-01-06T05:09:15.799762-06:00 linux-uc1g sudo: pam_systemd(sudo:session): pam_putenv: delete non-existent entry; XDG_RUNTIME_DIR
    Not seeing the same error as without the hub. Interesting. But then again there may be the same error but in a different location. I'll leave the analysis to you.

Page 1 of 3 123 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •