Results 1 to 6 of 6

Thread: Could not read a file (KDE/cmd)

  1. #1

    Default Could not read a file (KDE/cmd)

    Hi everyone,

    Good Day! I am having problems with my openSUSE installation. I was trying to backup a partition to an external HD but some files failed with an error "Could not read ..." like as shown below:

    This also happens when I try tocopy the same file within the local hard disk. Issuing a cp in cmd generated the same problem. I also encountered occasional freezing/hanging up. Sometimes when I try to click anything, it will freeze for 5-10 minutes. When this happens, everything is delayed until I reboot my openSUSE.

    my uname output:
    Code:
    Linux linux-nalix.site 3.4.11-2.16-desktop #1 SMP PREEMPT Wed Sep 26 17:05:00 UTC 2012 (259fc87) x86_64 x86_64 x86_64 GNU/Linux
    I am suspecting it is a hard disk problem? Though I hope it is not.

    /var/log/warn shows:

    Code:
    May 29 21:50:37 linux-nalix systemd-tmpfile[2716]: stat(/run/user/hoshirou/gvfs) fa
    iled: Permission denied
    May 29 22:03:20 linux-nalix if-up.d/21-dhcpcd-hook-samba: No dhcpcd info nor dhclie
    nt leases file found for eth1.
    May 30 02:08:58 linux-nalix kdm[751]: Cannot execute 'grub-set-default': not in $PA
    TH.
    May 30 08:17:18 linux-nalix udevd[315]: RUN+="socket:..." support will be removed f
    rom a future udev release. Please remove it from: /etc/udev/rules.d/71-multipath.ru
    les:7 and use libudev to subscribe to events.
    May 30 08:16:53 linux-nalix kernel: ACPI: RSDP 00000000000fe020 00024 (v02 ACRSYS)
    May 30 08:16:53 linux-nalix kernel: ACPI: XSDT 0000000096ffe120 00084 (v01 ACRSYS A
    CRPRDCT 00000001      01000013)
    May 30 08:16:53 linux-nalix kernel: ACPI: FACP 0000000096ffc000 000F4 (v04 ACRSYS A
    CRPRDCT 00000001 1025 00040000)
    May 30 08:16:53 linux-nalix kernel: ACPI: DSDT 0000000096fef000 0918D (v01 ACRSYS A
    CRPRDCT 00000000 1025 00040000)
    May 30 08:16:53 linux-nalix kernel: ACPI: FACS 0000000096f6d000 00040
    May 30 08:16:53 linux-nalix kernel: ACPI: ASF! 0000000096ffd000 000A5 (v32 ACRSYS A
    CRPRDCT 00000001 1025 00040000)
    May 30 08:16:53 linux-nalix kernel: ACPI: HPET 0000000096ffb000 00038 (v01 ACRSYS A
    CRPRDCT 00000001 1025 00040000)
    May 30 08:16:53 linux-nalix kernel: ACPI: FACS 0000000096f6d000 00040
    May 30 08:16:53 linux-nalix kernel: ACPI: ASF! 0000000096ffd000 000A5 (v32 ACRSYS A
    CRPRDCT 00000001 1025 00040000)
    May 30 08:16:53 linux-nalix kernel: ACPI: HPET 0000000096ffb000 00038 (v01 ACRSYS A
    CRPRDCT 00000001 1025 00040000)
    May 30 08:16:53 linux-nalix kernel: ACPI: APIC 0000000096ffa000 0008C (v02 ACRSYS ACRPRDCT 00000001 1025 00040000)
    May 30 08:16:53 linux-nalix kernel: ACPI: MCFG 0000000096ff9000 0003C (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
    May 30 08:16:53 linux-nalix kernel: ACPI: SLIC 0000000096fee000 00176 (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
    May 30 08:16:53 linux-nalix kernel: ACPI: SSDT 0000000096fed000 00BC2 (v01 ACRSYS ACRPRDCT 00001000 1025 00040000)
    May 30 08:16:53 linux-nalix kernel: ACPI: BOOT 0000000096feb000 00028 (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
    May 30 08:16:53 linux-nalix kernel: ACPI: ASPT 0000000096fe8000 00034 (v07 ACRSYS ACRPRDCT 00000001 1025 00040000)
    May 30 08:16:53 linux-nalix kernel: ACPI: SSDT 0000000096fe7000 007C2 (v01 ACRSYS ACRPRDCT 00003000 1025 00040000)
    May 30 08:16:53 linux-nalix kernel: ACPI: SSDT 0000000096fe6000 00996 (v01 ACRSYS ACRPRDCT 00003000 1025 00040000)
    May 30 08:16:53 linux-nalix kernel: Zone PFN ranges:
    May 30 08:16:53 linux-nalix kernel:   DMA      0x00000010 -> 0x00001000
    May 30 08:16:53 linux-nalix kernel:   DMA32    0x00001000 -> 0x00100000
    May 30 08:16:53 linux-nalix kernel:   Normal   0x00100000 -> 0x0015fe00
    May 30 08:16:53 linux-nalix kernel: Movable zone start PFN for each node
    May 30 08:16:53 linux-nalix kernel: Early memory PFN ranges
    May 30 08:16:53 linux-nalix kernel:     0: 0x00000010 -> 0x0000009d
    May 30 08:16:53 linux-nalix kernel:     0: 0x00000100 -> 0x00096e3f
    May 30 08:16:53 linux-nalix kernel:     0: 0x00096fff -> 0x00097000
    May 30 08:16:53 linux-nalix kernel:     0: 0x00100000 -> 0x0015fe00
    May 30 08:16:53 linux-nalix kernel: Built 1 zonelists in Node order, mobility grouping on.  Total pages: 990927
    May 30 08:16:53 linux-nalix kernel: Policy zone: Normal
    May 30 08:16:53 linux-nalix kernel: Fast TSC calibration using PIT
    May 30 08:16:53 linux-nalix kernel: Detected 2394.667 MHz processor.
    May 30 08:16:53 linux-nalix kernel: ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
    May 30 08:16:53 linux-nalix kernel: ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
    May 30 08:16:53 linux-nalix kernel: PEBS disabled due to CPU errata.
    May 30 08:16:53 linux-nalix kernel: Policy zone: Normal
    May 30 08:16:53 linux-nalix kernel: Fast TSC calibration using PIT
    May 30 08:16:53 linux-nalix kernel: Detected 2394.667 MHz processor.
    May 30 08:16:53 linux-nalix kernel: ENERGY_PERF_BIAS: Set to 'normal', was 'perform
    ance'
    May 30 08:16:53 linux-nalix kernel: ENERGY_PERF_BIAS: View and update with x86_ener
    gy_perf_policy(8)
    May 30 08:16:53 linux-nalix kernel: PEBS disabled due to CPU errata.
    May 30 08:16:53 linux-nalix kernel:  #2
    May 30 08:16:53 linux-nalix kernel:  #3
    May 30 08:16:53 linux-nalix kernel: ACPI: Executed 1 blocks of module-level executa
    ble AML code
    May 30 08:16:53 linux-nalix kernel: ACPI: SSDT 0000000096e70718 0067C (v01  PmRef  
    Cpu0Cst 00003001 INTL 20100121)
    May 30 08:16:53 linux-nalix kernel: ACPI: Dynamic OEM Table Load:
    May 30 08:16:53 linux-nalix kernel: ACPI: SSDT           (null) 0067C (v01  PmRef  Cpu0Cst 00003001 INTL 20100121)
    May 30 08:16:53 linux-nalix kernel: ACPI: SSDT 0000000096e71a98 00303 (v01  PmRef    ApIst 00003000 INTL 20100121)
    May 30 08:16:53 linux-nalix kernel: ACPI: Dynamic OEM Table Load:
    May 30 08:16:53 linux-nalix kernel: ACPI: SSDT           (null) 00303 (v01  PmRef    ApIst 00003000 INTL 20100121)
    May 30 08:16:53 linux-nalix kernel: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
    May 30 08:16:55 linux-nalix kernel: MXM: GUID detected in BIOS
    May 30 08:16:55 linux-nalix kernel: [drm:intel_dsm_platform_mux_info] *ERROR* MUX INFO call failed
    May 30 08:16:56 linux-nalix kernel: ACPI Exception: AE_NOT_FOUND, Evaluating _DOD (20120320/video-1149)
    May 30 08:16:56 linux-nalix kernel: video: probe of LNXVIDEO:01 failed with error 5
    May 30 08:16:56 linux-nalix kernel: [drm] nouveau 0000:01:00.0: 0xD518: i2c wr fail: -6
    May 30 08:17:08 linux-nalix kernel: firmware microcode: firmware_loading_store: unexpected value (0)
    May 30 08:17:09 linux-nalix kernel: mei: module is from the staging directory, the quality is unknown, you have been warned.
    :
    May 30 08:17:09 linux-nalix kernel: rts_pstor: module is from the staging directory
    , the quality is unknown, you have been warned.
    May 30 08:17:09 linux-nalix kernel: ACPI: Deprecated procfs I/F for AC is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
    May 30 08:17:09 linux-nalix kernel: wl: module license 'unspecified' taints kernel.
    May 30 08:17:09 linux-nalix kernel: Disabling lock debugging due to kernel taint
    May 30 08:17:10 linux-nalix kernel: ACPI Warning: 0x0000000000004040-0x000000000000405f SystemIO conflicts with Region \_SB_.PCI0.SBUS.SMBI 1 (20120320/utaddress-251)
    May 30 08:17:10 linux-nalix kernel: ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
    May 30 08:17:10 linux-nalix kernel: eth0: Broadcom BCM4358 802.11 Hybrid Wireless Controller 5.100.82.112
    May 30 08:17:11 linux-nalix kernel: sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
    May 30 08:17:11 linux-nalix kernel: sdhci-pci 0000:04:00.1: Will use DMA mode even though HW doesn't fully claim to support it.
    May 30 08:17:18 linux-nalix kernel: last message repeated 6 times
    May 30 08:17:17 linux-nalix kernel: vboxdrv: fAsync=0 offMin=0x141 offMax=0x1206
    May 30 08:17:22 linux-nalix kdm_config[749]: Multiple occurrences of key 'UseTheme' in section [X-*-Greeter] of /usr/share/kde4/config/kdm/kdmrc
    May 30 08:17:21 linux-nalix kernel: netlink: 12 bytes leftover after parsing attributes.
    May 30 08:17:32 linux-nalix kernel: last message repeated 6 times
    May 30 08:17:32 linux-nalix checkproc: checkproc: can not get session id for proces:
    May 30 08:17:51 linux-nalix pulseaudio[1843]: [pulseaudio] pid.c: Stale PID file, overwriting.
    May 30 08:18:05 linux-nalix pulseaudio[2007]: [pulseaudio] pid.c: Daemon already running.
    May 30 08:18:05 linux-nalix pulseaudio[2012]: [pulseaudio] pid.c: Daemon already running.
    May 30 08:18:29 linux-nalix kernel: CPU3: Package power limit notification (total events = 1)
    May 30 08:18:29 linux-nalix kernel: CPU1: Package power limit notification (total events = 1)
    May 30 08:18:29 linux-nalix kernel: CPU2: Package power limit notification (total events = 1)
    May 30 08:18:29 linux-nalix kernel: CPU0: Package power limit notification (total events = 1)
    May 30 08:20:00 linux-nalix udisksd[2151]: Error opening /etc/crypttab file: Failed to open file '/etc/crypttab': No such file or directory (g-file-error-quark, 4)
    May 30 08:20:48 linux-nalix udisksd[2151]: last message repeated 21 times
    Failing to copy a file regardless if via GUI or cmd and location (external or internal within the HD itself) is alarming. Having a linux that hangs up/lags is not good too. Something is wrong I just do not know what. It used to be ok. I hope someone can give me an idea on what I should check.

    Thank You in advance everyone!

  2. #2

    Default Re: Could not read a file (KDE/cmd)

    Quote Originally Posted by bimspramirez View Post
    Failing to copy a file regardless if via GUI or cmd and location (external or internal within the HD itself) is alarming. Having a linux that hangs up/lags is not good too. Something is wrong I just do not know what. It used to be ok. I hope someone can give me an idea on what I should check.

    Thank You in advance everyone!
    This does really sound like your hard disk has bad sectors.
    Could you upload the file /var/log/messages to susepaste.org and post a link?

  3. #3

    Default Re: Could not read a file (KDE/cmd)

    Quote Originally Posted by wolfi323 View Post
    This does really sound like your hard disk has bad sectors.
    Could you upload the file /var/log/messages to susepaste.org and post a link?
    Hi! Thanks for the reply! Here is the output:

    susepaste doesn't work for me, it tells me I am a spammer.

    I am putting pastebin link instead: var log - Pastebin.com

  4. #4

    Default Re: Could not read a file (KDE/cmd)

    Quote Originally Posted by bimspramirez View Post
    Hi! Thanks for the reply! Here is the output:

    susepaste doesn't work for me, it tells me I am a spammer.

    I am putting pastebin link instead: var log - Pastebin.com
    Hm, I don't find anything regarding bad sectors in there.

    Are you sure you have read permissions for those files? Right click on the file and select "Properties" to check.

    And please try to copy one again and post the output of "dmesg" after the error.

  5. #5
    Join Date
    Jun 2008
    Location
    Earth - Denmark
    Posts
    10,730

    Default Re: Could not read a file (KDE/cmd)

    On 05/30/2013 01:46 PM, bimspramirez wrote:
    > susepaste doesn't work for me, it tells me I am a spammer.


    that happened to me once....a few days later i tried to paste
    something different and it worked..

    i never figured out if the IP i was using that day had been
    blacklisted or if the image i was trying to upload was corrupted, or
    what exactly happened..(but i am sure it was not because i was
    spamming anything.)

    --
    dd

  6. #6

    Default Re: Could not read a file (KDE/cmd)

    Quote Originally Posted by wolfi323 View Post
    Hm, I don't find anything regarding bad sectors in there.

    Are you sure you have read permissions for those files? Right click on the file and select "Properties" to check.

    And please try to copy one again and post the output of "dmesg" after the error.
    Yes I do. For cmd, I logged on as root and issued cp command but got an error in KDE saying it could not read the file. Right now, I tried to do it again and now it works. But there is still occasional lags.

    pastebin for dmesg output: [ 0.507092] pci_root PNP0A08:00: host bridge window [mem 0x9fa00000-0xfeaffff - Pastebin.com


    Quote Originally Posted by DenverD View Post
    On 05/30/2013 01:46 PM, bimspramirez wrote:
    > susepaste doesn't work for me, it tells me I am a spammer.


    that happened to me once....a few days later i tried to paste
    something different and it worked..

    i never figured out if the IP i was using that day had been
    blacklisted or if the image i was trying to upload was corrupted, or
    what exactly happened..(but i am sure it was not because i was
    spamming anything.)

    --
    dd
    For pastebin, I also receive the same error but was given the captcha verification to be able to continue. For susepaste, it didn't give me that so I gave up.

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •