Results 1 to 2 of 2

Thread: How to get channels scanned in Kaffeine OSS 11.3?

Hybrid View

  1. #1
    Join Date
    Aug 2010
    Location
    California
    Posts
    190

    Question How to get channels scanned in Kaffeine OSS 11.3?

    I had a look at No TV in Kaffeine, but I'm lost. I have an HDTV wonder card. I have installed dvb, ffmpeg, w32-codecs, etc. I am able to watch video/hear audio.

    I have updated the scan data in kaffeine, adjusted device 1 tab to my area, but when I open the channels window and scan, it just goes through the motions and lists nothing. Here i partial output from:

    randolph@linux-jooj:~> scan /usr/share/dvb/atsc/us-NTSC-center-frequencies-8VSB
    scanning /usr/share/dvb/atsc/us-NTSC-center-frequencies-8VSB
    using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
    >>> tune to: 57000000:8VSB
    WARNING: >>> tuning failed!!!
    >>> tune to: 57000000:8VSB (tuning failed)
    WARNING: >>> tuning failed!!!
    >>> tune to: 63000000:8VSB
    WARNING: >>> tuning failed!!!
    >>> tune to: 63000000:8VSB (tuning failed)
    WARNING: >>> tuning failed!!!...

    The same over and over again until...

    >>> tune to: 797000000:8VSB (tuning failed)
    WARNING: >>> tuning failed!!!
    >>> tune to: 803000000:8VSB
    WARNING: >>> tuning failed!!!
    >>> tune to: 803000000:8VSB (tuning failed)
    WARNING: >>> tuning failed!!!
    dumping lists (0 services)
    Done.

    OK, what am I doing wrong? Please help. Thanks in advance.

    Randolph

  2. #2
    Join Date
    Aug 2010
    Location
    California
    Posts
    190

    Default Re: How to get channels scanned in Kaffeine OSS 11.3?

    Here is the output from dmesg (exerpt):

    [ 6.557230] IRQ 17/cx88[0]: IRQF_DISABLED is not guaranteed on shared IRQs
    [ 6.557254] cx88[0]/1: CX88x/0: ALSA support for cx2388x boards
    [ 6.598695] cx88/2: cx2388x dvb driver version 0.0.7 loaded
    [ 6.598698] cx88/2: registering cx8802 driver, type: dvb access: shared
    [ 6.598702] cx88[0]/2: subsystem: 1002:a101, board: ATI HDTV Wonder [card=34]
    [ 6.598704] cx88[0]/2: cx2388x based DVB/ATSC card
    [ 6.598706] cx8802_alloc_frontends() allocating 1 frontend(s)
    [ 6.719755] forcedeth 0000:00:0a.0: ifname eth0, PHY OUI 0x1374 @ 0, addr 00:17:31:56:8e:5a
    [ 6.719759] forcedeth 0000:00:0a.0: highdma csum gbit lnktim desc-v3
    [ 6.720155] k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141
    [ 6.721305] EDAC amd64: This node reports that Memory ECC is currently disabled, set F3x44[22] (0000:00:18.3).
    [ 6.721316] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
    [ 6.721318] Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
    [ 6.721319] (Note that use of the override may cause unknown side effects.)
    [ 6.721340] amd64_edac: probe of 0000:00:18.2 failed with error -22
    [ 6.723728] ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 22
    [ 6.723734] Intel ICH 0000:00:04.0: PCI INT A -> Link[APCJ] -> GSI 22 (level, low) -> IRQ 22
    [ 6.723786] Intel ICH 0000:00:04.0: setting latency timer to 64
    [ 6.915503] nxt200x: NXT2004 Detected
    [ 6.947944] tuner-simple 4-0061: creating new instance
    [ 6.947948] tuner-simple 4-0061: type set to 68 (Philips TUV1236D ATSC/NTSC dual in)
    [ 6.947952] DVB: registering new adapter (cx88[0])
    [ 6.947956] DVB: registering adapter 0 frontend 0 (Nextwave NXT200X VSB/QAM frontend)...
    [ 7.036020] intel8x0_measure_ac97_clock: measured 50714 usecs (2496 samples)
    [ 7.036023] intel8x0: clocking to 46813
    [ 7.170931] Adding 2103292k swap on /dev/sda5. Priority:-1 extents:1 across:2103292k
    [ 7.235233] scsi 6:0:0:0: Direct-Access Memorex TD Classic 003B PMAP PQ: 0 ANSI: 0 C...

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •