Results 1 to 6 of 6

Thread: Power Management options for UPS

  1. #1

    Post Power Management options for UPS

    Hello,

    I've attached a UPS to my server through USB. and sure enough up came a tab in Power Management Preferences for the UPS -- great.

    There are power low options as follows:
    "When UPS power is low"
    "When UPS power is critically low"

    The UPS sends a message to the computer when a threshold you set in the UPS is reached, in my case 25% of battery left.

    The obvious guess is that this warning from the UPS is the "When UPS power is low" however, I don't know. It's just a guess.

    Looking further at the data I can get from the UPS the battery data is as follows:

    battery.charge: 100
    battery.charge.low: 25
    battery.charge.warning: 50
    battery.runtime: 760
    battery.temperature: 36.9
    battery.type: PbAc
    battery.voltage: 53.4
    battery.voltage.nominal: 48.0

    The obvious relationships here are:

    "When UPS power is low" -> battery.charge.warning
    "When UPS power is critically low" -> battery.charge.low

    However, again, that's just a guess from what would make sense.

    So my first question is, is there a way to know this information, and is there a place were these critical points are set, or are they all from the UPS. I'm guess there are some settings somewhere because not all UPSs are going to be able to supply this information. Some may only supply a battery level or some just a warning message so there must be some configuration for this somewhere.

    My 2nd question is a probably a little harder to know the answer to. After getting this to work I wanted the added functionality of nut so I installed it and got it working and it uses the On UPS Power panel as far as I can tell.

    Through all the nut documentation it talks about powering down on once the battery level reaches the critical point (I assume that is "When UPS power is critically low"). I don't see anywhere however where it mentions handling "When UPS power is low" so now the question comes up, will it have any effect at all with nut installed, i.e. what will happen?

    Of course I can just "pull the plug" and start finding this stuff out but Linux is all about having the information and "knowing" (assuming all works as it should) I am asking to find out where this information would be -- and become smarter for it

    Thanks,
    Reg

  2. #2
    Join Date
    Jul 2010
    Location
    Adelaide, Australia
    Posts
    963

    Default Re: Power Management options for UPS

    You can use upsc to determine the battery.charge.warning and battery.charge.low

    e.g.

    Code:
    # upsc apc
    battery.charge: 100
    battery.charge.low: 10
    battery.charge.warning: 50
    battery.date: not set
    battery.mfr.date: 2009/11/29
    battery.runtime: 690
    battery.runtime.low: 120
    battery.type: PbAc
    battery.voltage: 13.5
    battery.voltage.nominal: 12.0
    driver.name: usbhid-ups
    driver.parameter.pollfreq: 30
    driver.parameter.pollinterval: 2
    driver.parameter.port: auto
    driver.version: 2.2.2
    driver.version.data: APC HID 0.92
    driver.version.internal: 0.33
    input.transfer.high: 266
    input.transfer.low: 180
    input.voltage: 232.0
    input.voltage.nominal: 230
    ups.beeper.status: enabled
    ups.delay.shutdown: 20
    ups.delay.start: 30
    ups.firmware: 871.O1 .I
    ups.firmware.aux: O1
    ups.load: 51
    ups.mfr: APC
    ups.mfr.date: 2009/11/29
    ups.model: Back-UPS ES 700G
    ups.productid: 0002
    ups.serial: 3B0948X82191
    ups.status: OL
    ups.timer.reboot: 0
    ups.timer.shutdown: -1
    ups.vendorid: 051d
    Desktop: Gigabyte GA-Z270-HD3 - Core i7 7700K - openSUSE Leap 42.2 KDE
    Laptop: HP EliteBook 8770W - Core i7 3940XM - openSUSE Leap 42.2 KDE

  3. #3
    Join Date
    Jan 2009
    Location
    Taft, Republic of California. UTC -8
    Posts
    1,474

    Default Re: Power Management options for UPS

    If it's an APC Backup UPS you can use acpupsd and its associated files.
    Tumbleweed

  4. #4

    Default Re: Power Management options for UPS

    Thanks for this but I am using upsc, which is how I was able to show the listing sample in my original post. The question revolves around relating the info. from upsc and other nut utilities to the Linux "Power Mangement Console" UPS tab. I.e.: what relates to what, what has no relationship, where is the configuration that links the various peices together, and so forth - I can't find the connection information between the two pieces of software. All my nut utilites work just fine.

    Quote Originally Posted by ah7013 View Post
    You can use upsc to determine the battery.charge.warning and battery.charge.low
    e.g.
    Code:
    # upsc apc
    battery.charge: 100

  5. #5

    Default Re: Power Management options for UPS

    Unfortunately it's a Tripp Lite (actually I like how it performs so I can't complain). However, even if it was an APC I'm not sure if this would answer my quesiton, as you can see from my above reply my quesiton revolves around two peices of software and discovering the relationship between the two.
    Quote Originally Posted by FlameBait View Post
    If it's an APC Backup UPS you can use acpupsd and its associated files.

  6. #6

    Default Re: Power Management options for UPS

    Thanks guys, I suspect the answer to this is not easily found so I think it's time to give up for now.

    Anyway, I'm having a configuration problem with nut, or a bug, not sure which yet but since it's a bit different to this question I'll make a new post for that issue.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •