Page 5 of 13 FirstFirst ... 34567 ... LastLast
Results 41 to 50 of 125

Thread: Cant find network folder

  1. #41

    Default Re: Cant find network folder

    Tnx novsan... There are troubles yea. Cause the hardware is found in Yast. But there is no interface configured for this device....

    In the hardware manager I can c the driver is not active.
    How can I reload the drivers -> rt2800sta and rt2x00sta? I cant find the directories.

  2. #42

    Default Re: Cant find network folder

    How can I reload the drivers -> rt2800sta and rt2x00sta? I cant find the directories.
    Hi!
    You need remove lines:
    Code:
    blacklist rt2800sta
    blacklist rt2x00sta
    at the end of the file /etc/modprobe.d/50-blacklist.conf
    After that you can load these drivers:
    Code:
    modprobe rt2800sta
    modprobe rt2x00sta
    And another question. There is already compiled rt2870sta.ko module in the /lib/modules/2.6.*/kernel/drivers/staging/ directory. Did you tried use it before than you've got compiled your own driver? It needs some additional firmware.
    Did you install it?

  3. #43

    Default Re: Cant find network folder

    Sorry, it's my fault - there isn't rt2800sta and rt2x00sta modules. There are rt2800usb and rt2x00usb modules

  4. #44

    Default Re: Cant find network folder

    Hi novsan, I only used my own rt2870sta.ko build.

    But now I c too it was already there in the kernel. I check for the firmware.
    But why it need firmware. Isnt the firmware running on the USB stick?

  5. #45

    Default Re: Cant find network folder

    No, firmware is loaded by driver, i think.
    You can download firmware ralink-firmware-1.1-1.1.noarch.rpm package here : Index of /repositories/driver:/wireless/11.2-update/noarch
    Or from ralinktech site: Ralink corp.
    If you will download from ralinktech site - unpuck archive and copy rt2870.bin file in /lib/firmware directory.
    After that, try to reload rt2870sta driver.

  6. #46

    Default Re: Cant find network folder

    Tnx novsan.... IOU !

  7. #47

    Default Re: Cant find network folder

    novsan.... I did all the instructions but still no wlan interface.
    I run collectNWData and this is the result->
    [code]
    Code:
    collectNWData.sh V0.6.3.4 (Rev: 1.220, Build: 2010/04/05 13:36:33 UTC)
    --- Which type of your network connection should be tested?
    --- (2) Wireless connection (WLAN)
    --- What's the type of networktopology?
    --- (1) WLAN access point <---> LinuxClient
    --- On which host is the script executed?
    --- (1) LinuxClient
    
    --- NWEliza is analyzing the system for common network configuration errors ...
    
    !!! CND0110E: For the selected connection type there was no active network interface found on your system
    !!! CND0310W: Classic network configuration with ifup was detected. Configuration with knetworkmanager is much easier
    
    --- Go to http://www.linux-tips-and-tricks.de/CND#English to get more detailed instructions 
    --- about the error/warning messages and how to fix the problems on your own.
    
    --- If you are unsuccessful then place the contents of file collectNWData.txt in the net
    --- (see http://www.linux-tips-and-tricks.de/CND_UPL#English for links) 
    --- and then paste the nopaste link on your favorite Linux forum.
    
    ==================================================================================================================
    ==================================================================================================================
    *** uname -a
    Linux linux-y4n6 2.6.31.5-0.1-desktop #1 SMP PREEMPT 2009-10-26 15:49:03 +0100 i686 athlon i386 GNU/Linux
    ==================================================================================================================
    *** cat /etc/*[-_]release || cat /etc/*[-_]version
    /etc/SuSE-release
    openSUSE 11.2 (i586)
    VERSION = 11.2
    ==================================================================================================================
    *** cat /etc/resolv | grep -i "nameserver"
    ==================================================================================================================
    *** cat /etc/hosts
    127.0.0.1       localhost
    127.0.0.2       linux-y4n6.site linux-y4n6
    ==================================================================================================================
    *** route -n
    Kernel IP routing table
    Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
    127.0.0.0       0.0.0.0         255.0.0.0       U     0      0        0 lo
    ==================================================================================================================
    *** ifconfig
    eth0      Link encap:Ethernet  HWaddr ##:##:##:##:##:#1  
              UP BROADCAST MULTICAST  MTU:1500  Metric:1
              RX packets:0 errors:0 dropped:0 overruns:0 frame:0
              TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 txqueuelen:1000 
              RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
              Interrupt:26 Base address:0x2000 
    lo        Link encap:Local Loopback  
              inet addr:127.0.0.1  Mask:255.0.0.0
              inet6 addr: ::1/128 Scope:Host
              UP LOOPBACK RUNNING  MTU:16436  Metric:1
              RX packets:130 errors:0 dropped:0 overruns:0 frame:0
              TX packets:130 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 txqueuelen:0 
              RX bytes:8476 (8.2 Kb)  TX bytes:8476 (8.2 Kb)
    ==================================================================================================================
    *** ping tests
    connect: Network is unreachable
    Ping of 195.135.220.3 failed
    ping: unknown host www.suse.de
    Ping of www.suse.de failed
    ==================================================================================================================
    *** dhcpcd-test
    ==================================================================================================================
    *** lspci
    00:06.0 Ethernet controller [0200]: nVidia Corporation MCP65 Ethernet [10de:0450] (rev a3)
    ==================================================================================================================
    *** lsusb
    Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
    Bus 001 Device 003: ID 07d1:3c0a D-Link System 
    Bus 001 Device 007: ID 1307:0165 Transcend Information, Inc. 2GB/4GB Flash Drive
    Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
    Bus 002 Device 002: ID 046d:c01d Logitech, Inc. MX510 Optical Mouse
    ==================================================================================================================
    *** hwinfo (filtered)
    16: PCI 06.0: 0200 Ethernet controller
      Model: "nVidia MCP65 Ethernet"
      Vendor: pci 0x10de "nVidia Corporation"
      Device: pci 0x0450 "MCP65 Ethernet"
      SubVendor: pci 0x1458 "Giga-byte Technology"
      SubDevice: pci 0xe000 
      Driver: "forcedeth"
      Driver Modules: "forcedeth"
      Device File: eth0
      Link detected: no
        Driver Status: forcedeth is active
        Driver Activation Cmd: "modprobe forcedeth"
    ==================================================================================================================
    *** lsmod # (filtered)
    | af_packet       | amd74xx         | cfg80211        | cpufreq_conservative| cpufreq_powersave |
    | cpufreq_userspace| crc16           | crc_ccitt       | edd             | fat              |
    | floppy          | forcedeth       | fuse            | i2c_nforce2     | ide_cd_mod       |
    | ide_gd_mod      | ieee1394        | input_polldev   | jbd2            | k8temp           |
    | mac80211        | nls_cp437       | nls_iso8859_1   | ohci1394        | pata_amd         |
    | powernow_k8     | ppdev           | rfkill          | rt2800usb       | rt2x00lib        |
    | rt2x00usb       | sg              | snd_hda_codec   | snd_hda_codec_realtek| snd_hda_intel    |
    | snd_hwdep       | snd_seq_device  | sr_mod          | st              | thermal          |
    | thermal_sys     | vfat            |
    ==================================================================================================================
    *** cat /etc/sysconfig/network/ifcfg-[earwd]*
    --- /etc/sysconfig/network/ifcfg-eth0
    BOOTPROTO='dhcp'
    BROADCAST=''
    ETHTOOL_OPTIONS=''
    IPADDR=''
    MTU=''
    NAME='MCP65 Ethernet'
    NETMASK=''
    NETWORK=''
    REMOTE_IPADDR=''
    STARTMODE='auto'
    USERCONTROL='no'
    ==================================================================================================================
    *** iwconfig
    lo        no wireless extensions.
    eth0      no wireless extensions.
    ==================================================================================================================
    *** Actual date for bias of following greps
    20:42:30 2010-03-27
    ==================================================================================================================
    *** grep -i radio /var/log/messages* | tail -n 5
    ==================================================================================================================
    *** dmesg | grep -i radio | tail -n 5
    ==================================================================================================================
    *** tail -n 300 /var/log/messages* | /bin/grep -i firmware | tail -n 5
    ==================================================================================================================
    *** ls /lib/firmware/*
    | 2.6.31.5-0.1-desktop    | 3com                    | acenic                  | adaptec                  |
    | advansys                | agere_ap_fw.bin         | agere_sta_fw.bin        | ar9170-1.fw              |
    | ar9170-2.fw             | atmsar11.fw             | av7110                  | bnx2                     |
    | bnx2x-e1-4.8.53.0.fw    | bnx2x-e1h-4.8.53.0.fw   | cis                     | cpia2                    |
    | cxgb3                   | dabusb                  | dsp56k                  | dvb-fe-xc5000-1.6.114.fw |
    | e100                    | edgeport                | emi26                   | emi62                    |
    | ess                     | i2400m-fw-usb-1.3.sbcf  | i2400m-fw-usb-1.4.sbcf  | intelliport2.bin         |
    | iwlwifi-1000-3.ucode    | iwlwifi-3945-2.ucode    | iwlwifi-4965-2.ucode    | iwlwifi-5000-1.ucode     |
    | iwlwifi-5000-2.ucode    | iwlwifi-5150-2.ucode    | kaweth                  | keyspan                  |
    | keyspan_pda             | korg                    | libertas                | LICENCE.agere            |
    | LICENCE.atheros_firmware| LICENCE.i2400m          | LICENCE.iwlwifi_firmware| LICENCE.libertas         |
    | LICENCE.mwl8k           | LICENCE.qla2xxx         | LICENCE.ralink-firmware.txt| LICENCE.xc5000           |
    | LICENSE.ralink-firmware.txt| mts_cdma.fw             | mts_edge.fw             | mts_gsm.fw               |
    | mwl8k                   | myricom                 | ositech                 | ql2100_fw.bin            |
    | ql2200_fw.bin           | ql2300_fw.bin           | ql2322_fw.bin           | ql2400_fw.bin            |
    | ql2500_fw.bin           | qlogic                  | rt2561.bin              | rt2561s.bin              |
    | rt2661.bin              | rt2860.bin              | rt2870.bin              | rt73.bin                 |
    | sb16                    | slicoss                 | sun                     | sxg                      |
    | tehuti                  | ti_3410.fw              | ti_5052.fw              | tigon                    |
    | tr_smctr.bin            | ttusb-budget            | usbdux                  | usbduxfast_firmware.bin  |
    | usbdux_firmware.bin     | v4l-cx231xx-avcore-01.fw| v4l-cx23418-apu.fw      | v4l-cx23418-cpu.fw       |
    | v4l-cx23418-dig.fw      | v4l-cx23885-avcore-01.fw| v4l-cx23885-enc.fw      | v4l-cx25840.fw           |
    | vicam                   | whiteheat.fw            | whiteheat_loader.fw     | yam                      |
    | yamaha                  |
    ==================================================================================================================
    *** ndiswrapper -l
    No ndiswrapper module loaded
    ==================================================================================================================
    *** Active processes
    wpa_supplicant:NO knetworkmanager:NO nm-applet:NO
    ==================================================================================================================
    *** egrep -i "persistent|networkmanager" /etc/sysconfig/network/config | grep -v "^#|^$"
    NETWORKMANAGER="no"
    ==================================================================================================================
    *** grep 'eth|ath|wlan|ra' /etc/udev/rules.d/*net_persistent* /etc/udev/rules.d/*persistent-net*
    /etc/udev/rules.d/70-persistent-net.rules:SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="##:##:##:##:##:#1", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0"
    ==================================================================================================================
    *** grep -r 'eth[0-10]|ath[0-10]|wlan[0-10]|ra[0-10]' /etc/modprobe.*
    ==================================================================================================================
    *** iwlist scanning
    No WLANs found
    ==================================================================================================================
    *** NWElizaStates
    DI:0 AP:0 NI:1 cNI:1 NDIS:0 NIWL:0 IP6:0 KM:0 WLW:0 RTDT:SuSE
    The firmware is an image. So it must reside in the Flash first time I boot the usb device. No? I cant belive it must be loaded everytime I boot my system.

  8. #48
    Join Date
    Jun 2008
    Location
    Kansas City Area, Missouri, USA
    Posts
    7,235

    Default Re: Cant find network folder

    On 04/19/2010 02:56 PM, In Control01 wrote:
    >
    > novsan.... I did all the instructions but still no wlan interface.
    > I run collectNWData and this is the result->


    The script shows no hardware device.

    You have done a lot of fooling around, yet I see no instance of you
    looking at the ID codes for the device. If it is PCI, post the output of
    '/sbin/lspci -nnk'. If it is a USB deevice, then post the output of the
    command 'lsusb'. NOTE: We do not need the entire output - only the
    section that describes your wireless device.


  9. #49

    Default Re: Cant find network folder

    Hi Iwfinger,

    This is my WLAN device->
    Code:
    Bus 001 Device 003: ID 07d1:3c0a D-Link System
    What interface it need?

  10. #50
    Join Date
    Jun 2008
    Location
    Kansas City Area, Missouri, USA
    Posts
    7,235

    Default Re: Cant find network folder

    On 04/19/2010 04:06 PM, In Control01 wrote:
    >
    > Hi Iwfinger,
    >
    > This is my WLAN device->
    >
    > Code:
    > --------------------
    >
    > Bus 001 Device 003: ID 07d1:3c0a D-Link System
    >
    > --------------------


    The driver for that device is rt2800usb, which is built into the kernel.
    If you have blacklisted any rt2800 drivers, please revert those changes.
    After you do that, issuing the command

    Code:
    sudo /sbin/modprobe -v  rt2800usb
    should allow you to see the device with

    Code:
    /usr/sbin/iwconfig
    You then need to check if firmware is available with

    Code:
    dmesg  |  egrep "firmware|rt2"
    I am assuming you have openSUSE 11.2.

Page 5 of 13 FirstFirst ... 34567 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •