Page 2 of 2 FirstFirst 12
Results 11 to 18 of 18

Thread: (Another) Wireless Issue

  1. #11

    Default Re: (Another) Wireless Issue

    Hm,

    Code:
    linux-yaos:/home/nick # modprobe -rv atmel_cs 
    FATAL: Module atmel_cs is in use. 
    linux-yaos:/home/nick # modprobe -v atmel_cs 
    linux-yaos:/home/nick # iwlist ethl scan 
    ethl      Interface doesn't support scanning. 
    That's not good, and I also wanted to see kernel messages on loading the module (which was not possible, as it could not be unloaded).

    OK, same procedure again (all commands as root)

    First console with the tail-command.

    - remove the card

    - unload moodule

    Code:
    modprobe -rv atmel_cs
    If it's not unloadable, reboot the machine without the card and start from the beginning.

    - insert card

    Code:
    modprobe -v atmel_cs
    (if the module is not loaded automatically, take a look at your monitoring console).

    Code:
    iwconfig
    
    iwlist scan
    
    ifconfig eth1 up
    
    iwconfig 
    
    iwlist scan
    Again, post output of both consoles.

  2. #12

    Default Re: (Another) Wireless Issue

    Quote Originally Posted by Akoellh View Post
    Hm,

    Code:
    linux-yaos:/home/nick # modprobe -rv atmel_cs 
    FATAL: Module atmel_cs is in use. 
    linux-yaos:/home/nick # modprobe -v atmel_cs 
    linux-yaos:/home/nick # iwlist ethl scan 
    ethl      Interface doesn't support scanning. 
    That's not good, and I also wanted to see kernel messages on loading the module (which was not possible, as it could not be unloaded).

    OK, same procedure again (all commands as root)

    First console with the tail-command.

    - remove the card

    - unload moodule

    Code:
    modprobe -rv atmel_cs
    If it's not unloadable, reboot the machine without the card and start from the beginning.

    - insert card

    Code:
    modprobe -v atmel_cs
    (if the module is not loaded automatically, take a look at your monitoring console).

    Code:
    iwconfig
    
    iwlist scan
    
    ifconfig eth1 up
    
    iwconfig 
    
    iwlist scan
    Again, post output of both consoles.
    Code:
    linux-yaos:/home/nick # modprobe -rv atmel_cs 
    rmmod /lib/modules/2.6.27.7-9-default/kernel/drivers/net/wireless/atmel_cs.ko 
    rmmod /lib/modules/2.6.27.7-9-default/kernel/drivers/net/wireless/atmel.ko 
    linux-yaos:/home/nick # iwconfig 
    lo        no wireless extensions. 
     
    eth0      no wireless extensions. 
     
    pan0      no wireless extensions. 
     
    linux-yaos:/home/nick # iwlist scan 
    lo        Interface doesn't support scanning. 
     
    eth0      Interface doesn't support scanning. 
     
    pan0      Interface doesn't support scanning. 
     
    linux-yaos:/home/nick # ifconfig eth1 up 
    eth1: unknown interface: No such device 
    linux-yaos:/home/nick # iwconfig ethl up 
    iwconfig: unknown command "up" 
    linux-yaos:/home/nick # iwconfig ethl1 
    ethl1     No such device 
     
    linux-yaos:/home/nick # iwconfig 
    lo        no wireless extensions. 
     
    eth0      no wireless extensions. 
     
    pan0      no wireless extensions. 
     
    linux-yaos:/home/nick # iwlist scan 
    lo        Interface doesn't support scanning. 
     
    eth0      Interface doesn't support scanning. 
     
    pan0      Interface doesn't support scanning. 
     
    linux-yaos:/home/nick #
    ^^That was both.

  3. #13

    Default Re: (Another) Wireless Issue

    And now again _without_ forgetting the second console and _without_ forgetting to load the module.

  4. #14

    Default Re: (Another) Wireless Issue

    Quote Originally Posted by Akoellh View Post
    And now again _without_ forgetting the second console and _without_ forgetting to load the module.
    Oh, sorry, I forgot to load the module again.

    Then I screwed up, so I rebooted the machine without the card, inserted again once ready, and ran then restarted the steps.

    This is the ENTIRE code I came up with (for all of them):

    Code:
    nick@linux-yaos:~> ls -1 /lib/firmware/atmel* 
    /lib/firmware/atmel_at76c502_3com.bin 
    /lib/firmware/atmel_at76c502_3com-wpa.bin 
    /lib/firmware/atmel_at76c502.bin 
    /lib/firmware/atmel_at76c502d.bin 
    /lib/firmware/atmel_at76c502d-wpa.bin 
    /lib/firmware/atmel_at76c502e.bin 
    /lib/firmware/atmel_at76c502e-wpa.bin 
    /lib/firmware/atmel_at76c502-wpa.bin 
    /lib/firmware/atmel_at76c503-i3861.bin 
    /lib/firmware/atmel_at76c503-i3863.bin 
    /lib/firmware/atmel_at76c503-rfmd-0.90.2-140.bin 
    /lib/firmware/atmel_at76c503-rfmd-acc.bin 
    /lib/firmware/atmel_at76c503-rfmd.bin 
    /lib/firmware/atmel_at76c504_2958-wpa.bin 
    /lib/firmware/atmel_at76c504a_2958-wpa.bin 
    /lib/firmware/atmel_at76c504.bin 
    /lib/firmware/atmel_at76c504c-wpa.bin 
    /lib/firmware/atmel_at76c505a-rfmd2958.bin 
    /lib/firmware/atmel_at76c505-rfmd2958.bin 
    /lib/firmware/atmel_at76c505-rfmd.bin 
    /lib/firmware/atmel_at76c506.bin 
    /lib/firmware/atmel_at76c506-wpa.bin 
    nick@linux-yaos:~> su 
    Password:  
    linux-yaos:/home/nick # modprove -rv atmel_cs 
    bash: modprove: command not found 
    linux-yaos:/home/nick # modprobe -rv atmel_cs 
    rmmod /lib/modules/2.6.27.7-9-default/kernel/drivers/pcmcia/pcmcia.ko 
    linux-yaos:/home/nick # modprone -v atmel_cs 
    bash: modprone: command not found 
    linux-yaos:/home/nick # modprobe -v atmel_cs 
    insmod /lib/modules/2.6.27.7-9-default/kernel/drivers/net/wireless/atmel.ko  
    insmod /lib/modules/2.6.27.7-9-default/kernel/drivers/pcmcia/pcmcia.ko  
    insmod /lib/modules/2.6.27.7-9-default/kernel/drivers/net/wireless/atmel_cs.ko  
    linux-yaos:/home/nick # iwlist ethl scan 
    ethl      Interface doesn't support scanning. 
     
    linux-yaos:/home/nick # iwconfig 
    lo        no wireless extensions. 
     
    eth0      no wireless extensions. 
     
    pan0      no wireless extensions. 
     
    linux-yaos:/home/nick # modprobe -rv atmel_cs 
    rmmod /lib/modules/2.6.27.7-9-default/kernel/drivers/net/wireless/atmel_cs.ko 
    rmmod /lib/modules/2.6.27.7-9-default/kernel/drivers/pcmcia/pcmcia.ko 
    rmmod /lib/modules/2.6.27.7-9-default/kernel/drivers/net/wireless/atmel.ko 
    linux-yaos:/home/nick # modprobe -v atmel_cs 
    insmod /lib/modules/2.6.27.7-9-default/kernel/drivers/net/wireless/atmel.ko  
    insmod /lib/modules/2.6.27.7-9-default/kernel/drivers/pcmcia/pcmcia.ko  
    insmod /lib/modules/2.6.27.7-9-default/kernel/drivers/net/wireless/atmel_cs.ko  
    linux-yaos:/home/nick # iwconfig 
    lo        no wireless extensions. 
     
    eth0      no wireless extensions. 
     
    pan0      no wireless extensions. 
     
    eth1      IEEE 802.11-DS  ESSID:off/any   
              Mode:Managed  Frequency:2.427 GHz  Access Point: FF:00:00:00:00:00    
              Bit Rate:11 Mb/s    
              Retry short limit:7   RTS thr:off   Fragment thr:off 
              Encryption key:off 
              Power Management:off 
              Link Quality:0  Signal level:0  Noise level:0 
              Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0 
              Tx excessive retries:0  Invalid misc:0   Missed beacon:0 
     
    linux-yaos:/home/nick # iwlist scan 
    lo        Interface doesn't support scanning. 
     
    eth0      Interface doesn't support scanning. 
     
    pan0      Interface doesn't support scanning. 
     
    eth1      Interface doesn't support scanning : Device or resource busy 
     
    linux-yaos:/home/nick # ifconfig eth1 up 
    linux-yaos:/home/nick # iwconfig ethl up 
    iwconfig: unknown command "up" 
    linux-yaos:/home/nick # iwconfig 
    lo        no wireless extensions. 
     
    eth0      no wireless extensions. 
     
    pan0      no wireless extensions. 
     
    eth1      IEEE 802.11-DS  ESSID:off/any   
              Mode:Managed  Frequency:2.427 GHz  Access Point: FF:00:00:00:00:00    
              Bit Rate:11 Mb/s    
              Retry short limit:7   RTS thr:off   Fragment thr:off 
              Encryption key:off 
              Power Management:off 
              Link Quality:0  Signal level:0  Noise level:0 
              Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0 
              Tx excessive retries:0  Invalid misc:0   Missed beacon:0 
     
    linux-yaos:/home/nick # iwlist scan 
    lo        Interface doesn't support scanning. 
     
    eth0      Interface doesn't support scanning. 
     
    pan0      Interface doesn't support scanning.
    And then for the first one, which you called the "control" window:

    Code:
    nick@linux-yaos:~> su -c "tail -F /var/log/messages" 
    Password:  
    Apr 11 20:29:23 linux-yaos kernel: Bluetooth: BNEP (Ethernet Emulation) ver 1.3 
    Apr 11 20:29:23 linux-yaos kernel: Bluetooth: BNEP filters: protocol multicast 
    Apr 11 20:29:23 linux-yaos kernel: Bridge firewalling registered 
    Apr 11 20:29:23 linux-yaos kernel: pan0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature. 
    Apr 11 20:29:23 linux-yaos bluetoothd[2968]: bridge pan0 created 
    Apr 11 20:29:23 linux-yaos bluetoothd[2968]: Parsing /etc/bluetooth/input.conf failed: No such file or directory 
    Apr 11 20:29:23 linux-yaos ifup: Service network not started and mode 'auto' -> skipping 
    Apr 11 20:30:59 linux-yaos su: FAILED SU (to root) nick on /dev/pts/1 
    Apr 11 20:31:18 linux-yaos su: (to root) nick on /dev/pts/1 
    Apr 11 20:32:29 linux-yaos su: (to root) nick on /dev/pts/2 
    Apr 11 20:33:09 linux-yaos su: (to root) nick on /dev/pts/3 
    Apr 11 20:35:44 linux-yaos kernel: pccard: PCMCIA card inserted into slot 0 
    Apr 11 20:35:58 linux-yaos kernel: cs: memory probe 0xa0000000-0xa0ffffff: clean. 
    Apr 11 20:35:58 linux-yaos kernel: pcmcia: registering new device pcmcia0.0 
    Apr 11 20:35:59 linux-yaos kernel: irq 3: nobody cared (try booting with the "irqpoll" option) 
    Apr 11 20:35:59 linux-yaos kernel: Pid: 3311, comm: modprobe Tainted: G          2.6.27.7-9-default #1 
    Apr 11 20:35:59 linux-yaos kernel:  [<c0106570>] dump_trace+0x6b/0x249 
    Apr 11 20:35:59 linux-yaos kernel:  [<c01070a5>] show_trace+0x20/0x39 
    Apr 11 20:35:59 linux-yaos kernel:  [<c0343c02>] dump_stack+0x71/0x76 
    Apr 11 20:35:59 linux-yaos kernel:  [<c0163599>] __report_bad_irq+0x36/0x75 
    Apr 11 20:35:59 linux-yaos kernel:  [<c016367a>] note_interrupt+0xa2/0xe0 
    Apr 11 20:35:59 linux-yaos kernel:  [<c0163d0e>] handle_level_irq+0xa3/0xe4 
    Apr 11 20:35:59 linux-yaos kernel:  [<c01077c0>] do_IRQ+0x57/0x73 
    Apr 11 20:35:59 linux-yaos kernel:  [<c0105d23>] common_interrupt+0x23/0x30 
    Apr 11 20:35:59 linux-yaos kernel:  [<c012f953>] __do_softirq+0x74/0x119 
    Apr 11 20:35:59 linux-yaos kernel:  [<c012fa3d>] do_softirq+0x45/0x53 
    Apr 11 20:35:59 linux-yaos kernel:  [<c012fb45>] irq_exit+0x35/0x69 
    Apr 11 20:36:00 linux-yaos kernel:  [<c01077c5>] do_IRQ+0x5c/0x73 
    Apr 11 20:36:00 linux-yaos kernel:  [<c0105d23>] common_interrupt+0x23/0x30 
    Apr 11 20:36:00 linux-yaos kernel:  [<c03459f0>] _spin_unlock_irqrestore+0x1d/0x28 
    Apr 11 20:36:00 linux-yaos kernel:  [<c01632c5>] setup_irq+0x1d1/0x20d 
    Apr 11 20:36:00 linux-yaos kernel:  [<c016337d>] request_irq+0x7c/0x98 
    Apr 11 20:36:00 linux-yaos kernel:  [<dcf5ac4f>] init_atmel_card+0x2f0/0x3f5 [atmel] 
    Apr 11 20:36:00 linux-yaos kernel:  [<dcf262cd>] atmel_config+0x259/0x2b5 [atmel_cs] 
    Apr 11 20:36:00 linux-yaos kernel:  [<dcf62773>] pcmcia_device_probe+0xb7/0x126 [pcmcia] 
    Apr 11 20:36:00 linux-yaos kernel:  [<c02a1862>] really_probe+0xd7/0x1de 
    Apr 11 20:36:00 linux-yaos kernel:  [<c02a1a3e>] __driver_attach+0x37/0x55 
    Apr 11 20:36:00 linux-yaos kernel:  [<c02a111d>] bus_for_each_dev+0x31/0x57 
    Apr 11 20:36:00 linux-yaos kernel:  [<c02a1614>] driver_attach+0x16/0x18 
    Apr 11 20:36:00 linux-yaos kernel:  [<c02a0b16>] bus_add_driver+0xec/0x21b 
    Apr 11 20:36:00 linux-yaos kernel:  [<c02a1bb1>] driver_register+0x85/0xe2 
    Apr 11 20:36:00 linux-yaos kernel:  [<dcf6357e>] pcmcia_register_driver+0xc5/0xf4 [pcmcia] 
    Apr 11 20:36:00 linux-yaos kernel:  [<c010112b>] _stext+0x3b/0x127 
    Apr 11 20:36:00 linux-yaos kernel:  [<c014c8bf>] sys_init_module+0x8a/0x19e 
    Apr 11 20:36:00 linux-yaos kernel:  [<c0104c9b>] sysenter_do_call+0x12/0x2f 
    Apr 11 20:36:00 linux-yaos kernel:  [<ffffe430>] 0xffffe430 
    Apr 11 20:36:00 linux-yaos ifup: Network interface is managed from NetworkManager 
    Apr 11 20:36:00 linux-yaos kernel:  ======================= 
    Apr 11 20:36:01 linux-yaos kernel: handlers: 
    Apr 11 20:36:01 linux-yaos kernel: [<dcf5c563>] (service_interrupt+0x0/0x354 [atmel]) 
    Apr 11 20:36:01 linux-yaos kernel: Disabling IRQ #3 
    Apr 11 20:36:01 linux-yaos kernel: eth1: Atmel at76c50x. Version 0.98. MAC 00:00:1c:0b:a5:b4 
    Apr 11 20:36:01 linux-yaos kernel: Uniform Multi-Platform E-IDE driver 
    Apr 11 20:36:01 linux-yaos ifup: NetworkManager will be advised to set up eth1  
    Apr 11 20:36:01 linux-yaos ifup: but it cannot be assured from here. 
    Apr 11 20:36:05 linux-yaos kernel: firmware: requesting atmel_at76c502-wpa.bin 
    Apr 11 20:36:05 linux-yaos kernel: ADDRCONF(NETDEV_UP): eth1: link is not ready 
    Apr 11 20:36:05 linux-yaos kernel: firmware: requesting atmel_at76c502-wpa.bin 
    Apr 11 20:36:05 linux-yaos kernel: firmware: requesting atmel_at76c502-wpa.bin 
    Apr 11 20:36:05 linux-yaos kernel: firmware: requesting atmel_at76c502-wpa.bin 
    Apr 11 20:36:05 linux-yaos kernel: NET: Registered protocol family 17 
    Apr 11 20:36:05 linux-yaos kernel: firmware: requesting atmel_at76c502-wpa.bin 
    Apr 11 20:36:06 linux-yaos kernel: firmware: requesting atmel_at76c502-wpa.bin 
    Apr 11 20:36:06 linux-yaos kernel: firmware: requesting atmel_at76c502-wpa.bin 
    Apr 11 20:36:06 linux-yaos kernel: firmware: requesting atmel_at76c502-wpa.bin 
    Apr 11 20:36:06 linux-yaos kernel: firmware: requesting atmel_at76c502-wpa.bin 
    Apr 11 20:37:49 linux-yaos kernel: usb 1-2: new full speed USB device using ohci_hcd and address 2 
    Apr 11 20:37:49 linux-yaos kernel: usb 1-2: configuration #1 chosen from 1 choice 
    Apr 11 20:37:49 linux-yaos kernel: usb 1-2: New USB device found, idVendor=12f7, idProduct=1a00 
    Apr 11 20:37:49 linux-yaos kernel: usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 
    Apr 11 20:37:49 linux-yaos kernel: usb 1-2: Product: TD Classic 003B  
    Apr 11 20:37:49 linux-yaos kernel: usb 1-2: Manufacturer: Memorex  
    Apr 11 20:37:49 linux-yaos kernel: usb 1-2: SerialNumber: 07680C1505C7 
    Apr 11 20:37:50 linux-yaos kernel: Initializing USB Mass Storage driver... 
    Apr 11 20:37:50 linux-yaos kernel: scsi2 : SCSI emulation for USB Mass Storage devices 
    Apr 11 20:37:50 linux-yaos kernel: usbcore: registered new interface driver usb-storage 
    Apr 11 20:37:50 linux-yaos kernel: USB Mass Storage support registered. 
    Apr 11 20:37:50 linux-yaos kernel: usb-storage: device found at 2 
    Apr 11 20:37:50 linux-yaos kernel: usb-storage: waiting for device to settle before scanning 
    Apr 11 20:37:51 linux-yaos kernel: scsi 2:0:0:0: Direct-Access     Memorex  TD Classic 003B  PMAP PQ: 0 ANSI: 0 CCS 
    Apr 11 20:37:52 linux-yaos kernel: sd 2:0:0:0: [sdb] 2015232 512-byte hardware sectors: (1.03GB/984MiB) 
    Apr 11 20:37:52 linux-yaos kernel: sd 2:0:0:0: [sdb] Write Protect is off 
    Apr 11 20:37:52 linux-yaos kernel: sd 2:0:0:0: [sdb] Mode Sense: 23 00 00 00 
    Apr 11 20:37:52 linux-yaos kernel: sd 2:0:0:0: [sdb] Assuming drive cache: write through 
    Apr 11 20:37:52 linux-yaos kernel: sd 2:0:0:0: [sdb] 2015232 512-byte hardware sectors: (1.03GB/984MiB) 
    Apr 11 20:37:52 linux-yaos kernel: sd 2:0:0:0: [sdb] Write Protect is off 
    Apr 11 20:37:52 linux-yaos kernel: sd 2:0:0:0: [sdb] Mode Sense: 23 00 00 00 
    Apr 11 20:37:52 linux-yaos kernel: sd 2:0:0:0: [sdb] Assuming drive cache: write through 
    Apr 11 20:37:52 linux-yaos kernel:  sdb: sdb1 
    Apr 11 20:37:52 linux-yaos kernel: sd 2:0:0:0: [sdb] Attached SCSI removable disk 
    Apr 11 20:37:52 linux-yaos kernel: sd 2:0:0:0: Attached scsi generic sg2 type 0 
    Apr 11 20:37:52 linux-yaos kernel: usb-storage: device scan complete 
    Apr 11 20:37:54 linux-yaos gnome-keyring-daemon[2844]: adding removable location: volume_uuid_E537_6866 at /media/TravelDrive 
    Apr 11 20:37:54 linux-yaos hald: mounted /dev/sdb1 on behalf of uid 1000

  5. #15

    Default Re: (Another) Wireless Issue

    Not good.

    Code:
    Apr 11 20:35:59 linux-yaos kernel: Pid: 3311, comm: modprobe Tainted: G          2.6.27.7-9-default #1 
    Apr 11 20:35:59 linux-yaos kernel:  [<c0106570>] dump_trace+0x6b/0x249 
    Apr 11 20:35:59 linux-yaos kernel:  [<c01070a5>] show_trace+0x20/0x39 
    Apr 11 20:35:59 linux-yaos kernel:  [<c0343c02>] dump_stack+0x71/0x76 
    Apr 11 20:35:59 linux-yaos kernel:  [<c0163599>] __report_bad_irq+0x36/0x75 
    Apr 11 20:35:59 linux-yaos kernel:  [<c016367a>] note_interrupt+0xa2/0xe0 
    Apr 11 20:35:59 linux-yaos kernel:  [<c0163d0e>] handle_level_irq+0xa3/0xe4 
    Apr 11 20:35:59 linux-yaos kernel:  [<c01077c0>] do_IRQ+0x57/0x73 
    Apr 11 20:35:59 linux-yaos kernel:  [<c0105d23>] common_interrupt+0x23/0x30 
    Apr 11 20:35:59 linux-yaos kernel:  [<c012f953>] __do_softirq+0x74/0x119 
    Apr 11 20:35:59 linux-yaos kernel:  [<c012fa3d>] do_softirq+0x45/0x53 
    Apr 11 20:35:59 linux-yaos kernel:  [<c012fb45>] irq_exit+0x35/0x69 
    Apr 11 20:36:00 linux-yaos kernel:  [<c01077c5>] do_IRQ+0x5c/0x73 
    Apr 11 20:36:00 linux-yaos kernel:  [<c0105d23>] common_interrupt+0x23/0x30 
    Apr 11 20:36:00 linux-yaos kernel:  [<c03459f0>] _spin_unlock_irqrestore+0x1d/0x28 
    Apr 11 20:36:00 linux-yaos kernel:  [<c01632c5>] setup_irq+0x1d1/0x20d 
    Apr 11 20:36:00 linux-yaos kernel:  [<c016337d>] request_irq+0x7c/0x98 
    Apr 11 20:36:00 linux-yaos kernel:  [<dcf5ac4f>] init_atmel_card+0x2f0/0x3f5 [atmel] 
    Apr 11 20:36:00 linux-yaos kernel:  [<dcf262cd>] atmel_config+0x259/0x2b5 [atmel_cs] 
    Apr 11 20:36:00 linux-yaos kernel:  [<dcf62773>] pcmcia_device_probe+0xb7/0x126 [pcmcia] 
    Apr 11 20:36:00 linux-yaos kernel:  [<c02a1862>] really_probe+0xd7/0x1de 
    Apr 11 20:36:00 linux-yaos kernel:  [<c02a1a3e>] __driver_attach+0x37/0x55 
    Apr 11 20:36:00 linux-yaos kernel:  [<c02a111d>] bus_for_each_dev+0x31/0x57 
    Apr 11 20:36:00 linux-yaos kernel:  [<c02a1614>] driver_attach+0x16/0x18 
    Apr 11 20:36:00 linux-yaos kernel:  [<c02a0b16>] bus_add_driver+0xec/0x21b 
    Apr 11 20:36:00 linux-yaos kernel:  [<c02a1bb1>] driver_register+0x85/0xe2 
    Apr 11 20:36:00 linux-yaos kernel:  [<dcf6357e>] pcmcia_register_driver+0xc5/0xf4 [pcmcia] 
    Apr 11 20:36:00 linux-yaos kernel:  [<c010112b>] _stext+0x3b/0x127 
    Apr 11 20:36:00 linux-yaos kernel:  [<c014c8bf>] sys_init_module+0x8a/0x19e 
    Apr 11 20:36:00 linux-yaos kernel:  [<c0104c9b>] sysenter_do_call+0x12/0x2f 
    Apr 11 20:36:00 linux-yaos kernel:  [<ffffe430>] 0xffffe430
    Kernel problem when initializing the card, but:

    Code:
    Apr 11 20:35:59 linux-yaos kernel: irq 3: nobody cared 
    (try booting with the "irqpoll" option)
    Reboot the machine and type

    irqpoll

    before starting openSUSE (can be seen in the line Boot Options).

    Same procedure again.

  6. #16

    Default Re: (Another) Wireless Issue

    Quote Originally Posted by Akoellh View Post
    Not good.

    Code:
    Apr 11 20:35:59 linux-yaos kernel: Pid: 3311, comm: modprobe Tainted: G          2.6.27.7-9-default #1 
    Apr 11 20:35:59 linux-yaos kernel:  [<c0106570>] dump_trace+0x6b/0x249 
    Apr 11 20:35:59 linux-yaos kernel:  [<c01070a5>] show_trace+0x20/0x39 
    Apr 11 20:35:59 linux-yaos kernel:  [<c0343c02>] dump_stack+0x71/0x76 
    Apr 11 20:35:59 linux-yaos kernel:  [<c0163599>] __report_bad_irq+0x36/0x75 
    Apr 11 20:35:59 linux-yaos kernel:  [<c016367a>] note_interrupt+0xa2/0xe0 
    Apr 11 20:35:59 linux-yaos kernel:  [<c0163d0e>] handle_level_irq+0xa3/0xe4 
    Apr 11 20:35:59 linux-yaos kernel:  [<c01077c0>] do_IRQ+0x57/0x73 
    Apr 11 20:35:59 linux-yaos kernel:  [<c0105d23>] common_interrupt+0x23/0x30 
    Apr 11 20:35:59 linux-yaos kernel:  [<c012f953>] __do_softirq+0x74/0x119 
    Apr 11 20:35:59 linux-yaos kernel:  [<c012fa3d>] do_softirq+0x45/0x53 
    Apr 11 20:35:59 linux-yaos kernel:  [<c012fb45>] irq_exit+0x35/0x69 
    Apr 11 20:36:00 linux-yaos kernel:  [<c01077c5>] do_IRQ+0x5c/0x73 
    Apr 11 20:36:00 linux-yaos kernel:  [<c0105d23>] common_interrupt+0x23/0x30 
    Apr 11 20:36:00 linux-yaos kernel:  [<c03459f0>] _spin_unlock_irqrestore+0x1d/0x28 
    Apr 11 20:36:00 linux-yaos kernel:  [<c01632c5>] setup_irq+0x1d1/0x20d 
    Apr 11 20:36:00 linux-yaos kernel:  [<c016337d>] request_irq+0x7c/0x98 
    Apr 11 20:36:00 linux-yaos kernel:  [<dcf5ac4f>] init_atmel_card+0x2f0/0x3f5 [atmel] 
    Apr 11 20:36:00 linux-yaos kernel:  [<dcf262cd>] atmel_config+0x259/0x2b5 [atmel_cs] 
    Apr 11 20:36:00 linux-yaos kernel:  [<dcf62773>] pcmcia_device_probe+0xb7/0x126 [pcmcia] 
    Apr 11 20:36:00 linux-yaos kernel:  [<c02a1862>] really_probe+0xd7/0x1de 
    Apr 11 20:36:00 linux-yaos kernel:  [<c02a1a3e>] __driver_attach+0x37/0x55 
    Apr 11 20:36:00 linux-yaos kernel:  [<c02a111d>] bus_for_each_dev+0x31/0x57 
    Apr 11 20:36:00 linux-yaos kernel:  [<c02a1614>] driver_attach+0x16/0x18 
    Apr 11 20:36:00 linux-yaos kernel:  [<c02a0b16>] bus_add_driver+0xec/0x21b 
    Apr 11 20:36:00 linux-yaos kernel:  [<c02a1bb1>] driver_register+0x85/0xe2 
    Apr 11 20:36:00 linux-yaos kernel:  [<dcf6357e>] pcmcia_register_driver+0xc5/0xf4 [pcmcia] 
    Apr 11 20:36:00 linux-yaos kernel:  [<c010112b>] _stext+0x3b/0x127 
    Apr 11 20:36:00 linux-yaos kernel:  [<c014c8bf>] sys_init_module+0x8a/0x19e 
    Apr 11 20:36:00 linux-yaos kernel:  [<c0104c9b>] sysenter_do_call+0x12/0x2f 
    Apr 11 20:36:00 linux-yaos kernel:  [<ffffe430>] 0xffffe430
    Kernel problem when initializing the card, but:

    Code:
    Apr 11 20:35:59 linux-yaos kernel: irq 3: nobody cared 
    (try booting with the "irqpoll" option)
    Reboot the machine and type

    irqpoll

    before starting openSUSE (can be seen in the line Boot Options).

    Same procedure again.
    Ah, thanks, that somehow got my internet working once I entered that and went through the same procedure.

    Code:
    nick@linux-yaos:~> ls -l /lib/firmware/atmel* 
    -rw-r--r-- 1 root root 30348 2008-12-03 00:02 /lib/firmware/atmel_at76c502_3com.bin 
    -rw-r--r-- 1 root root 35184 2008-12-03 00:02 /lib/firmware/atmel_at76c502_3com-wpa.bin 
    -rw-r--r-- 1 root root 31764 2008-12-03 00:02 /lib/firmware/atmel_at76c502.bin 
    -rw-r--r-- 1 root root 31764 2008-12-03 00:02 /lib/firmware/atmel_at76c502d.bin 
    -rw-r--r-- 1 root root 35276 2008-12-03 00:02 /lib/firmware/atmel_at76c502d-wpa.bin 
    -rw-r--r-- 1 root root 31776 2008-12-03 00:02 /lib/firmware/atmel_at76c502e.bin 
    -rw-r--r-- 1 root root 35272 2008-12-03 00:02 /lib/firmware/atmel_at76c502e-wpa.bin 
    -rw-r--r-- 1 root root 35276 2009-04-11 17:14 /lib/firmware/atmel_at76c502-wpa.bin 
    -rw-r--r-- 1 root root 28164 2008-12-03 00:02 /lib/firmware/atmel_at76c503-i3861.bin 
    -rw-r--r-- 1 root root 28040 2008-12-03 00:02 /lib/firmware/atmel_at76c503-i3863.bin 
    -rw-r--r-- 1 root root 35372 2008-12-03 00:02 /lib/firmware/atmel_at76c503-rfmd-0.90.2-140.bin 
    -rw-r--r-- 1 root root 37804 2008-12-03 00:02 /lib/firmware/atmel_at76c503-rfmd-acc.bin 
    -rw-r--r-- 1 root root 37964 2008-12-03 00:02 /lib/firmware/atmel_at76c503-rfmd.bin 
    -rw-r--r-- 1 root root 35180 2008-12-03 00:02 /lib/firmware/atmel_at76c504_2958-wpa.bin 
    -rw-r--r-- 1 root root 39928 2008-12-03 00:02 /lib/firmware/atmel_at76c504a_2958-wpa.bin 
    -rw-r--r-- 1 root root 31748 2008-12-03 00:02 /lib/firmware/atmel_at76c504.bin 
    -rw-r--r-- 1 root root 35196 2008-12-03 00:02 /lib/firmware/atmel_at76c504c-wpa.bin 
    -rw-r--r-- 1 root root 37009 2008-12-03 00:02 /lib/firmware/atmel_at76c505a-rfmd2958.bin 
    -rw-r--r-- 1 root root 37000 2008-12-03 00:02 /lib/firmware/atmel_at76c505-rfmd2958.bin 
    -rw-r--r-- 1 root root 35532 2008-12-03 00:02 /lib/firmware/atmel_at76c505-rfmd.bin 
    -rw-r--r-- 1 root root 31824 2008-12-03 00:02 /lib/firmware/atmel_at76c506.bin 
    -rw-r--r-- 1 root root 35228 2008-12-03 00:02 /lib/firmware/atmel_at76c506-wpa.bin 
    nick@linux-yaos:~> su 
    Password:  
    linux-yaos:/home/nick # modprobe -rv atmel_cs 
    FATAL: Module atmel_cs is in use. 
    linux-yaos:/home/nick # modprobe -v atmel_cs 
    linux-yaos:/home/nick # iwlist eth1 scan 
    eth1      Scan completed : 
              Cell 01 - Address: 00:12:17:0D:07:96 
                        ESSID:"linksys" 
                        Mode:Managed 
                        Channel:6 
                        Quality:9/100  Signal level:9/100  Noise level:0/0 
                        Encryption key:off 
     
    linux-yaos:/home/nick # iwconfig 
    lo        no wireless extensions. 
     
    eth0      no wireless extensions. 
     
    eth1      IEEE 802.11-DS  ESSID:"linksys"   
              Mode:Managed  Frequency:2.437 GHz  Access Point: 00:12:17:0D:07:96    
              Bit Rate:11 Mb/s    
              Retry short limit:7   RTS thr:off   Fragment thr:off 
              Encryption key:off 
              Power Management:off 
              Link Quality=66/100  Signal level=39/100   
              Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0 
              Tx excessive retries:0  Invalid misc:0   Missed beacon:22 
     
    pan0      no wireless extensions. 
     
    linux-yaos:/home/nick #
    Code:
    nick@linux-yaos:~> su -c "tail -F /var/log/messages" 
    Password:  
    Apr 11 21:04:15 linux-yaos bluetoothd[3055]: Failed to find Bluetooth netlink family 
    Apr 11 21:04:15 linux-yaos bluetoothd[3055]: Parsing /etc/bluetooth/network.conf failed: No such file or directory 
    Apr 11 21:04:16 linux-yaos kernel: Bluetooth: BNEP (Ethernet Emulation) ver 1.3 
    Apr 11 21:04:16 linux-yaos kernel: Bluetooth: BNEP filters: protocol multicast 
    Apr 11 21:04:17 linux-yaos kernel: Bridge firewalling registered 
    Apr 11 21:04:17 linux-yaos kernel: pan0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature. 
    Apr 11 21:04:17 linux-yaos bluetoothd[3055]: bridge pan0 created 
    Apr 11 21:04:18 linux-yaos bluetoothd[3055]: Parsing /etc/bluetooth/input.conf failed: No such file or directory 
    Apr 11 21:04:18 linux-yaos ifup: Service network not started and mode 'auto' -> skipping 
    Apr 11 21:06:20 linux-yaos su: (to root) nick on /dev/pts/1 
    Apr 11 21:09:31 linux-yaos su: (to root) nick on /dev/pts/2 
    Apr 11 21:10:29 linux-yaos kernel: firmware: requesting atmel_at76c502-wpa.bin 
    Apr 11 21:10:29 linux-yaos kernel: firmware: requesting atmel_at76c502-wpa.bin 
    Apr 11 21:10:29 linux-yaos kernel: firmware: requesting atmel_at76c502-wpa.bin 
    Apr 11 21:10:29 linux-yaos kernel: firmware: requesting atmel_at76c502-wpa.bin 
    Apr 11 21:10:29 linux-yaos kernel: firmware: requesting atmel_at76c502-wpa.bin 
    Apr 11 21:10:29 linux-yaos kernel: firmware: requesting atmel_at76c502-wpa.bin 
    Apr 11 21:10:29 linux-yaos kernel: firmware: requesting atmel_at76c502-wpa.bin 
    Apr 11 21:10:30 linux-yaos kernel: firmware: requesting atmel_at76c502-wpa.bin 
    Apr 11 21:10:30 linux-yaos kernel: firmware: requesting atmel_at76c502-wpa.bin 
    Apr 11 21:10:30 linux-yaos kernel: firmware: requesting atmel_at76c502-wpa.bin 
    Apr 11 21:10:30 linux-yaos kernel: firmware: requesting atmel_at76c502-wpa.bin 
    Apr 11 21:10:31 linux-yaos dhclient: Internet Systems Consortium DHCP Client V3.1.1 
    Apr 11 21:10:31 linux-yaos dhclient: Copyright 2004-2008 Internet Systems Consortium. 
    Apr 11 21:10:31 linux-yaos dhclient: All rights reserved. 
    Apr 11 21:10:31 linux-yaos dhclient: For info, please visit http://www.isc.org/sw/dhcp/ 
    Apr 11 21:10:31 linux-yaos dhclient:  
    Apr 11 21:10:31 linux-yaos dhclient: Listening on LPF/eth1/00:00:1c:0b:a5:b4 
    Apr 11 21:10:31 linux-yaos dhclient: Sending on   LPF/eth1/00:00:1c:0b:a5:b4 
    Apr 11 21:10:31 linux-yaos dhclient: Sending on   Socket/fallback 
    Apr 11 21:10:33 linux-yaos dhclient: DHCPDISCOVER on eth1 to 255.255.255.255 port 67 interval 5 
    Apr 11 21:10:33 linux-yaos kernel: martian source 255.255.255.255 from 192.168.1.1, on dev eth1 
    Apr 11 21:10:33 linux-yaos kernel: ll header: ff:ff:ff:ff:ff:ff:00:12:17:0d:07:94:08:00 
    Apr 11 21:10:33 linux-yaos dhclient: DHCPOFFER from 192.168.1.1 
    Apr 11 21:10:38 linux-yaos dhclient: DHCPREQUEST on eth1 to 255.255.255.255 port 67 
    Apr 11 21:10:38 linux-yaos kernel: martian source 255.255.255.255 from 192.168.1.1, on dev eth1 
    Apr 11 21:10:38 linux-yaos kernel: ll header: ff:ff:ff:ff:ff:ff:00:12:17:0d:07:94:08:00 
    Apr 11 21:10:38 linux-yaos dhclient: DHCPACK from 192.168.1.1 
    Apr 11 21:10:38 linux-yaos dhclient: bound to 192.168.1.117 -- renewal in 1640 seconds. 
    Apr 11 21:10:38 linux-yaos avahi-daemon[2354]: Joining mDNS multicast group on interface eth1.IPv4 with address 192.168.1.117. 
    Apr 11 21:10:38 linux-yaos avahi-daemon[2354]: New relevant interface eth1.IPv4 for mDNS. 
    Apr 11 21:10:38 linux-yaos avahi-daemon[2354]: Registering new address record for 192.168.1.117 on eth1.IPv4. 
    Apr 11 21:10:40 linux-yaos nm-dispatcher.action: Script '/etc/NetworkManager/dispatcher.d/autofs' exited with error status 1. 
    Apr 11 21:10:40 linux-yaos if-up.d/21-dhcpcd-hook-samba: No dhcpcd info nor dhclient leases file found for eth1. 
    Apr 11 21:10:41 linux-yaos sm-notify[3550]: Already notifying clients; Exiting! 
    Apr 11 21:10:41 linux-yaos nm-dispatcher.action: Script '/etc/NetworkManager/dispatcher.d/nfs' exited with error status 6. 
    Apr 11 21:27:22 linux-yaos kernel: usb 1-2: new full speed USB device using ohci_hcd and address 2 
    Apr 11 21:27:22 linux-yaos kernel: usb 1-2: configuration #1 chosen from 1 choice 
    Apr 11 21:27:22 linux-yaos kernel: usb 1-2: New USB device found, idVendor=12f7, idProduct=1a00 
    Apr 11 21:27:22 linux-yaos kernel: usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 
    Apr 11 21:27:22 linux-yaos kernel: usb 1-2: Product: TD Classic 003B  
    Apr 11 21:27:22 linux-yaos kernel: usb 1-2: Manufacturer: Memorex  
    Apr 11 21:27:22 linux-yaos kernel: usb 1-2: SerialNumber: 07680C1505C7 
    Apr 11 21:27:22 linux-yaos kernel: Initializing USB Mass Storage driver... 
    Apr 11 21:27:22 linux-yaos kernel: scsi2 : SCSI emulation for USB Mass Storage devices 
    Apr 11 21:27:22 linux-yaos kernel: usbcore: registered new interface driver usb-storage 
    Apr 11 21:27:22 linux-yaos kernel: USB Mass Storage support registered. 
    Apr 11 21:27:22 linux-yaos kernel: usb-storage: device found at 2 
    Apr 11 21:27:22 linux-yaos kernel: usb-storage: waiting for device to settle before scanning 
    Apr 11 21:27:23 linux-yaos kernel: scsi 2:0:0:0: Direct-Access     Memorex  TD Classic 003B  PMAP PQ: 0 ANSI: 0 CCS 
    Apr 11 21:27:24 linux-yaos kernel: sd 2:0:0:0: [sdb] 2015232 512-byte hardware sectors: (1.03GB/984MiB) 
    Apr 11 21:27:24 linux-yaos kernel: sd 2:0:0:0: [sdb] Write Protect is off 
    Apr 11 21:27:24 linux-yaos kernel: sd 2:0:0:0: [sdb] Mode Sense: 23 00 00 00 
    Apr 11 21:27:24 linux-yaos kernel: sd 2:0:0:0: [sdb] Assuming drive cache: write through 
    Apr 11 21:27:24 linux-yaos kernel: sd 2:0:0:0: [sdb] 2015232 512-byte hardware sectors: (1.03GB/984MiB) 
    Apr 11 21:27:24 linux-yaos kernel: sd 2:0:0:0: [sdb] Write Protect is off 
    Apr 11 21:27:24 linux-yaos kernel: sd 2:0:0:0: [sdb] Mode Sense: 23 00 00 00 
    Apr 11 21:27:24 linux-yaos kernel: sd 2:0:0:0: [sdb] Assuming drive cache: write through 
    Apr 11 21:27:24 linux-yaos kernel:  sdb: sdb1 
    Apr 11 21:27:24 linux-yaos kernel: sd 2:0:0:0: [sdb] Attached SCSI removable disk 
    Apr 11 21:27:24 linux-yaos kernel: sd 2:0:0:0: Attached scsi generic sg2 type 0 
    Apr 11 21:27:24 linux-yaos kernel: usb-storage: device scan complete 
    Apr 11 21:27:27 linux-yaos gnome-keyring-daemon[2953]: adding removable location: volume_uuid_E537_6866 at /media/TravelDrive 
    Apr 11 21:27:27 linux-yaos hald: mounted /dev/sdb1 on behalf of uid 1000

  7. #17

    Default Re: (Another) Wireless Issue

    And now the last step is to add this parameter permanently to your boot options.

    - Start a text editor as root

    - open the file "boot/grub/menu.lst"

    - search for the lines starting with "kernel" and add

    irqpoll

    to the respective lines.

    Save and you're done.

  8. #18

    Default Re: (Another) Wireless Issue

    Quote Originally Posted by Akoellh View Post
    And now the last step is to add this parameter permanently to your boot options.

    - Start a text editor as root

    - open the file "boot/grub/menu.lst"

    - search for the lines starting with "kernel" and add

    irqpoll

    to the respective lines.

    Save and you're done.
    Where do I add irqpoll on the lines?

Page 2 of 2 FirstFirst 12

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •