Page 1 of 2 12 LastLast
Results 1 to 10 of 14

Thread: USB Configuration

  1. #1

    Thumbs down USB Configuration

    I have tried to connect a few devices to my USB ports, and my mp3 that is windows only will power & charge. However, when I connect my Palm phone, I get no charge not sync. How do I determine if my USB is set up properly and is working?? Thanks in advance.

  2. #2
    Join Date
    Jun 2008
    Location
    Podunk
    Posts
    32,339
    Blog Entries
    15

    Default Re: USB Configuration

    On Tue, 22 Jul 2008 02:26:03 GMT
    susenewbe <susenewbe@no-mx.forums.opensuse.org> wrote:

    >
    > I have tried to connect a few devices to my USB ports, and my mp3 that
    > is windows only will power & charge. However, when I connect my Palm
    > phone, I get no charge not sync. How do I determine if my USB is set
    > up properly and is working?? Thanks in advance.
    >
    >

    Hi
    When you plug the palm in, run the dmesg command from a console (you
    may also see something here if you plug in your mp3 device), this should
    show you which /dev/ttyUSB port it's connected too. Then you need to
    configure your application to use that.

    --
    Cheers Malcolm (Linux Counter #276890)
    SLED 10 SP2 i586 Kernel 2.6.16.60-0.25-default
    up 3:30, 1 user, load average: 0.06, 0.29, 0.45
    GPU GeForce Go 6600 TE/6200 TE Version: 173.14.09


  3. #3

    Default Re: USB Configuration

    Code:
    visor 1-1:1.0: Handspring Visor / Palm OS converter detected
    usb 1-1: Handspring Visor / Palm OS converter now attached to ttyUSB0
    usb 1-1: Handspring Visor / Palm OS converter now attached to ttyUSB1
    usb 1-1: New USB device found, idVendor=0830, idProduct=0061
    usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=5
    usb 1-1: Product: Palm Handheld
    usb 1-1: Manufacturer: PalmOne, Inc.
    usb 1-1: SerialNumber: PalmSN12345678
    usb 1-1: USB disconnect, address 4
    visor ttyUSB0: Handspring Visor / Palm OS converter now disconnected from ttyUSB
    0
    visor ttyUSB1: Handspring Visor / Palm OS converter now disconnected from ttyUSB
    1
    visor 1-1:1.0: device disconnected
    atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
    atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    Uniform Multi-Platform E-IDE driver
    ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    st: Version 20080221, fixed bufsize 32768, s/g segs 256
    Driver 'st' needs updating - please use bus_type methods
    end_request: I/O error, dev fd0, sector 0
    end_request: I/O error, dev fd0, sector 0
    parport_pc 00:0b: disabled
    parport 0x378 (WARNING): CTR: wrote 0x0c, read 0xff
    parport 0x378 (WARNING): DATA: wrote 0xaa, read 0xff
    parport 0x378: You gave this address, but there is probably no parallel port the
    re!
    parport0: PC-style at 0x378 [PCSPP,TRISTATE]
    lp0: using parport0 (polling).
    IT8705 SuperIO detected.
    parport_pc 00:0b: activated
    parport_pc 00:0b: reported by Plug and Play ACPI
    parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA
    ]
    lp0: using parport0 (interrupt-driven).
    parport_pc 00:0b: disabled
    parport 0x378 (WARNING): CTR: wrote 0x0c, read 0xff
    parport 0x378 (WARNING): DATA: wrote 0xaa, read 0xff
    parport 0x378: You gave this address, but there is probably no parallel port the                                                           re!
    parport0: PC-style at 0x378 [PCSPP,TRISTATE]
    lp0: using parport0 (polling).
    ppa: Version 2.07 (for Linux 2.4.x)
    end_request: I/O error, dev fd0, sector 0
    end_request: I/O error, dev fd0, sector 0
    end_request: I/O error, dev fd0, sector 0
    end_request: I/O error, dev fd0, sector 0
    usb 3-2: USB disconnect, address 2
    atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    Here is the bottom portion of what I found. Does this help??

  4. #4
    Join Date
    Jun 2008
    Location
    Podunk
    Posts
    32,339
    Blog Entries
    15

    Default Re: USB Configuration

    On Tue, 22 Jul 2008 02:46:04 GMT
    susenewbe <susenewbe@no-mx.forums.opensuse.org> wrote:

    >
    > Code:
    > --------------------
    >
    > visor 1-1:1.0: Handspring Visor / Palm OS converter detected
    > usb 1-1: Handspring Visor / Palm OS converter now attached to
    > ttyUSB0 usb 1-1: Handspring Visor / Palm OS converter now attached to
    > ttyUSB1 usb 1-1: New USB device found, idVendor=0830, idProduct=0061
    > usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=5
    > usb 1-1: Product: Palm Handheld
    > usb 1-1: Manufacturer: PalmOne, Inc.
    > usb 1-1: SerialNumber: PalmSN12345678
    > usb 1-1: USB disconnect, address 4
    > visor ttyUSB0: Handspring Visor / Palm OS converter now
    > disconnected from ttyUSB 0
    > visor ttyUSB1: Handspring Visor / Palm OS converter now
    > disconnected from ttyUSB 1
    > visor 1-1:1.0: device disconnected

    <snip>
    > --------------------
    >
    > Here is the bottom portion of what I found. Does this help??

    Hi
    The Palm device is using either /dev/ttyUSB0 or /dev/ttyUSB1

    So what application are you using for syncing?

    My Palm died a while back, stuck with a blackberry now, almost have the
    tethering going. On a Palm it was a breeze.

    --
    Cheers Malcolm (Linux Counter #276890)
    SLED 10 SP2 i586 Kernel 2.6.16.60-0.25-default
    up 3:50, 1 user, load average: 0.14, 0.04, 0.12
    GPU GeForce Go 6600 TE/6200 TE Version: 173.14.09


  5. #5

    Default Re: USB Configuration

    trying to use KPilot. Not finding it...Will try to see if I can get it going tomorrow.

  6. #6
    Join Date
    Jun 2008
    Location
    Podunk
    Posts
    32,339
    Blog Entries
    15

    Default Re: USB Configuration

    On Tue, 22 Jul 2008 03:26:03 GMT
    susenewbe <susenewbe@no-mx.forums.opensuse.org> wrote:

    >
    > trying to use KPilot. Not finding it...Will try to see if I can get it
    > going tomorrow.
    >
    >

    Hi
    OK, I can get the Treo out of the draw and charge it... and have a look
    also.

    --
    Cheers Malcolm (Linux Counter #276890)
    SLED 10 SP2 i586 Kernel 2.6.16.60-0.25-default
    up 4:29, 1 user, load average: 0.26, 0.30, 0.33
    GPU GeForce Go 6600 TE/6200 TE Version: 173.14.09


  7. #7
    Join Date
    Jun 2008
    Location
    Podunk
    Posts
    32,339
    Blog Entries
    15

    Default Re: USB Configuration

    On Tue, 22 Jul 2008 03:33:37 GMT
    Malcolm <malcolm_nospamlewis@bellsouth.net> wrote:

    > On Tue, 22 Jul 2008 03:26:03 GMT
    > susenewbe <susenewbe@no-mx.forums.opensuse.org> wrote:
    >
    > >
    > > trying to use KPilot. Not finding it...Will try to see if I can get
    > > it going tomorrow.
    > >
    > >

    > Hi
    > OK, I can get the Treo out of the draw and charge it... and have a
    > look also.
    >

    Hi
    Well I tried it out and had to set the device to /dev/ttyUSB1 for it to
    communicate. Settings->Configure kPilot->Device. Then press your
    hotsync button.

    --
    Cheers Malcolm (Linux Counter #276890)
    SLED 10 SP2 i586 Kernel 2.6.16.60-0.25-default
    up 4:06, 1 user, load average: 0.96, 0.79, 1.09
    GPU GeForce Go 6600 TE/6200 TE Version: 173.14.09


  8. #8

    Default Re: USB Configuration

    Code:
    hub 2-0:1.0: unable to enumerate USB device on port 1
    usb 1-1: new full speed USB device using uhci_hcd and address 2
    usb 1-1: configuration #1 chosen from 1 choice
    usb 1-1: New USB device found, idVendor=0830, idProduct=0061
    usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=5
    usb 1-1: Product: Palm Handheld
    usb 1-1: Manufacturer: PalmOne, Inc.
    usb 1-1: SerialNumber: PalmSN12345678
    usbcore: registered new interface driver usbserial
    drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
    usbcore: registered new interface driver usbserial_generic
    drivers/usb/serial/usb-serial.c: USB Serial Driver core
    drivers/usb/serial/usb-serial.c: USB Serial support registered for Handspring Vi
    sor / Palm OS
    drivers/usb/serial/usb-serial.c: USB Serial support registered for Sony Clie 3.5
    drivers/usb/serial/usb-serial.c: USB Serial support registered for Sony Clie 5.0
    visor 1-1:1.0: Handspring Visor / Palm OS converter detected
    usb 1-1: Handspring Visor / Palm OS converter now attached to ttyUSB0
    usb 1-1: Handspring Visor / Palm OS converter now attached to ttyUSB1
    usbcore: registered new interface driver visor
    drivers/usb/serial/visor.c: USB HandSpring Visor / Palm OS driver
    atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
    usb 1-1: USB disconnect, address 2
    visor ttyUSB0: Handspring Visor / Palm OS converter now disconnected from ttyUSB
    0
    visor ttyUSB1: Handspring Visor / Palm OS converter now disconnected from ttyUSB
    1
    visor 1-1:1.0: device disconnected
    usb 1-1: new full speed USB device using uhci_hcd and address 3
    usb 1-1: configuration #1 chosen from 1 choice
    visor 1-1:1.0: Handspring Visor / Palm OS converter detected
    usb 1-1: Handspring Visor / Palm OS converter now attached to ttyUSB0
    usb 1-1: Handspring Visor / Palm OS converter now attached to ttyUSB1
    usb 1-1: New USB device found, idVendor=0830, idProduct=0061
    usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=5
    usb 1-1: Product: Palm Handheld
    usb 1-1: Manufacturer: PalmOne, Inc.
    usb 1-1: SerialNumber: PalmSN12345678
    usb 1-1: USB disconnect, address 3
    visor ttyUSB0: Handspring Visor / Palm OS converter now disconnected from ttyUSB
    0
    visor ttyUSB1: Handspring Visor / Palm OS converter now disconnected from ttyUSB
    1
    visor 1-1:1.0: device disconnected
    atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    usb 1-1: new full speed USB device using uhci_hcd and address 4

  9. #9

    Default Re: USB Configuration

    Code:
    usb 1-1: configuration #1 chosen from 1 choice
    visor 1-1:1.0: Handspring Visor / Palm OS converter detected
    usb 1-1: Handspring Visor / Palm OS converter now attached to ttyUSB0
    usb 1-1: Handspring Visor / Palm OS converter now attached to ttyUSB1
    usb 1-1: New USB device found, idVendor=0830, idProduct=0061
    usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=5
    usb 1-1: Product: Palm Handheld
    usb 1-1: Manufacturer: PalmOne, Inc.
    usb 1-1: SerialNumber: PalmSN12345678
    usb 1-1: USB disconnect, address 4
    visor ttyUSB0: Handspring Visor / Palm OS converter now disconnected from ttyUSB
    0
    visor ttyUSB1: Handspring Visor / Palm OS converter now disconnected from ttyUSB
    1
    visor 1-1:1.0: device disconnected
    atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
    atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    Uniform Multi-Platform E-IDE driver
    ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    st: Version 20080221, fixed bufsize 32768, s/g segs 256
    Driver 'st' needs updating - please use bus_type methods
    end_request: I/O error, dev fd0, sector 0
    end_request: I/O error, dev fd0, sector 0
    parport_pc 00:0b: disabled
    parport 0x378 (WARNING): CTR: wrote 0x0c, read 0xff
    parport 0x378 (WARNING): DATA: wrote 0xaa, read 0xff
    parport 0x378: You gave this address, but there is probably no parallel port the
    re!
    parport0: PC-style at 0x378 [PCSPP,TRISTATE]
    lp0: using parport0 (polling).
    IT8705 SuperIO detected.
    parport_pc 00:0b: activated
    parport_pc 00:0b: reported by Plug and Play ACPI
    parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA
    ]
    lp0: using parport0 (interrupt-driven).
    parport_pc 00:0b: disabled
    parport 0x378 (WARNING): CTR: wrote 0x0c, read 0xff
    parport 0x378 (WARNING): DATA: wrote 0xaa, read 0xff
    parport 0x378: You gave this address, but there is probably no parallel port the
    re!
    parport0: PC-style at 0x378 [PCSPP,TRISTATE]
    lp0: using parport0 (polling).
    ppa: Version 2.07 (for Linux 2.4.x)
    end_request: I/O error, dev fd0, sector 0
    end_request: I/O error, dev fd0, sector 0
    end_request: I/O error, dev fd0, sector 0
    end_request: I/O error, dev fd0, sector 0
    usb 3-2: USB disconnect, address 2
    atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
    atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
    atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).

  10. #10

    Default Re: USB Configuration

    Code:
    usb 3-1: USB disconnect, address 3
    sd 2:0:0:3: Device offlined - not ready after error recovery
    sd 2:0:0:2: [sde] READ CAPACITY failed
    sd 2:0:0:2: [sde] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_O
    K
    sd 2:0:0:2: [sde] Sense not available.
    sd 2:0:0:2: [sde] Write Protect is off
    sd 2:0:0:2: [sde] Mode Sense: 00 00 00 00
    sd 2:0:0:2: [sde] Assuming drive cache: write through
    sd 2:0:0:2: [sde] READ CAPACITY failed
    sd 2:0:0:2: [sde] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_O
    K
    sd 2:0:0:2: [sde] Sense not available.
    sd 2:0:0:2: [sde] Write Protect is off
    sd 2:0:0:2: [sde] Mode Sense: 00 00 00 00
    sd 2:0:0:2: [sde] Assuming drive cache: write through
    sd 2:0:0:1: [sdd] READ CAPACITY failed
    sd 2:0:0:1: [sdd] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_O
    K
    sd 2:0:0:1: [sdd] Sense not available.
    sd 2:0:0:1: [sdd] Write Protect is off
    sd 2:0:0:1: [sdd] Mode Sense: 00 00 00 00
    sd 2:0:0:1: [sdd] Assuming drive cache: write through
    sd 2:0:0:1: [sdd] READ CAPACITY failed
    sd 2:0:0:1: [sdd] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_O
    K
    sd 2:0:0:1: [sdd] Sense not available.
    sd 2:0:0:1: [sdd] Write Protect is off
    sd 2:0:0:1: [sdd] Mode Sense: 00 00 00 00
    sd 2:0:0:1: [sdd] Assuming drive cache: write through
    sd 2:0:0:0: [sdc] READ CAPACITY failed
    sd 2:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_O
    K
    sd 2:0:0:0: [sdc] Sense not available.
    sd 2:0:0:0: [sdc] Write Protect is off
    sd 2:0:0:0: [sdc] Mode Sense: 00 00 00 00
    sd 2:0:0:0: [sdc] Assuming drive cache: write through
    sd 2:0:0:0: [sdc] READ CAPACITY failed
    sd 2:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_O
    K
    sd 2:0:0:0: [sdc] Sense not available.
    sd 2:0:0:0: [sdc] Write Protect is off
    sd 2:0:0:0: [sdc] Mode Sense: 00 00 00 00
    sd 2:0:0:0: [sdc] Assuming drive cache: write through
    sd 2:0:0:1: [sdd] READ CAPACITY failed
    sd 2:0:0:1: [sdd] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_O
    K
    sd 2:0:0:1: [sdd] Sense not available.
    sd 2:0:0:2: [sde] READ CAPACITY failed
    sd 2:0:0:2: [sde] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_O
    K
    sd 2:0:0:2: [sde] Sense not available.
    sd 2:0:0:0: [sdc] READ CAPACITY failed
    sd 2:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_O
    K
    sd 2:0:0:0: [sdc] Sense not available.
    sd 2:0:0:1: [sdd] Write Protect is off
    sd 2:0:0:1: [sdd] Mode Sense: 00 00 00 00
    sd 2:0:0:1: [sdd] Assuming drive cache: write through
    sd 2:0:0:2: [sde] Write Protect is off
    sd 2:0:0:2: [sde] Mode Sense: 00 00 00 00
    sd 2:0:0:2: [sde] Assuming drive cache: write through
    sd 2:0:0:0: [sdc] Write Protect is off
    sd 2:0:0:0: [sdc] Mode Sense: 00 00 00 00
    sd 2:0:0:0: [sdc] Assuming drive cache: write through
    sd 2:0:0:0: [sdc] READ CAPACITY failed
    sd 2:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_O
    K
    sd 2:0:0:0: [sdc] Sense not available.
    sd 2:0:0:1: [sdd] READ CAPACITY failed
    sd 2:0:0:1: [sdd] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_O
    K
    sd 2:0:0:1: [sdd] Sense not available.
    sd 2:0:0:0: [sdc] Write Protect is off
    sd 2:0:0:0: [sdc] Mode Sense: 00 00 00 00
    sd 2:0:0:0: [sdc] Assuming drive cache: write through
    sd 2:0:0:2: [sde] READ CAPACITY failed
    sd 2:0:0:2: [sde] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_O
    K
    sd 2:0:0:2: [sde] Sense not available.
    sd 2:0:0:1: [sdd] Write Protect is off
    sd 2:0:0:1: [sdd] Mode Sense: 00 00 00 00
    sd 2:0:0:1: [sdd] Assuming drive cache: write through
    sd 2:0:0:2: [sde] Write Protect is off
    sd 2:0:0:2: [sde] Mode Sense: 00 00 00 00
    sd 2:0:0:2: [sde] Assuming drive cache: write through
    usb 3-1: new full speed USB device using uhci_hcd and address 7
    usb 3-1: device descriptor read/64, error -110
    usb 3-1: device descriptor read/64, error -110
    usb 3-1: new full speed USB device using uhci_hcd and address 8
    atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    usb 3-1: device descriptor read/64, error -110
    usb 3-1: device descriptor read/64, error -110
    usb 3-1: new full speed USB device using uhci_hcd and address 9
    usb 3-1: device not accepting address 9, error -110
    usb 3-1: new full speed USB device using uhci_hcd and address 10
    usb 3-1: device not accepting address 10, error -110
    hub 3-0:1.0: unable to enumerate USB device on port 1
    usb usb3: Controller not stopped yet!
    atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
    usb 3-1: new full speed USB device using uhci_hcd and address 11
    usb 3-1: device descriptor read/64, error -110
    usb 3-1: device descriptor read/64, error -110
    usb 3-1: new full speed USB device using uhci_hcd and address 12
    usb 3-1: device descriptor read/64, error -110
    usb 3-1: device descriptor read/64, error -110
    usb 3-1: new full speed USB device using uhci_hcd and address 13
    usb 3-1: device not accepting address 13, error -110
    usb 3-1: new full speed USB device using uhci_hcd and address 14
    usb 3-1: device not accepting address 14, error -110
    hub 3-0:1.0: unable to enumerate USB device on port 1
    usb usb3: Controller not stopped yet!
    atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
    usb 3-1: new full speed USB device using uhci_hcd and address 15
    usb 3-1: device descriptor read/64, error -110
    usb 3-1: device descriptor read/64, error -110
    usb 3-1: new full speed USB device using uhci_hcd and address 16
    usb 3-1: device descriptor read/64, error -110
    usb 3-1: device descriptor read/64, error -110
    usb 3-1: new full speed USB device using uhci_hcd and address 17
    usb 3-1: device not accepting address 17, error -110
    usb 3-1: new full speed USB device using uhci_hcd and address 18
    atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    This is the full dmeag, I tried USB3 to no avail. Any suggestions???

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •