wlan0 IEEE 802.11g ESSID:"AP11"
Mode:Managed Frequency:2.412 GHz Access Point: 00:0A:79:6E:21:8B
Bit Rate=54 Mb/s Tx-Power=27 dBm
Retry min limit:7 RTS thrff Fragment thr=2352 B
Encryption keyff
Link Quality=85/100 Signal level=-58 dBm Noise level=-92 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0

#ifconfig wlan0 inet 192.168.1.111
#ifconfig


wlan0 Link encap:Ethernet HWaddr 00:13:E8A:21:61
inet addr:192.168.1.111 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:51 errors:0 dropped:0 overruns:0 frame:0
TX packets:64 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:30499 (29.7 Kb) TX bytes:9895 (9.6 Kb)

wmaster0 Link encap:UNSPEC HWaddr 00-13-E8-DA-21-61-00-00-00-00-00-00-00-00-00-00
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

#ping 192.168.1.1

PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
64 bytes from 192.168.1.1: icmp_seq=1 ttl=250 time=4.01 ms
64 bytes from 192.168.1.1: icmp_seq=2 ttl=250 time=0.370 ms
64 bytes from 192.168.1.1: icmp_seq=7 ttl=250 time=0.380 ms
64 bytes from 192.168.1.1: icmp_seq=8 ttl=250 time=0.371 ms
64 bytes from 192.168.1.1: icmp_seq=9 ttl=250 time=0.378 ms


You are able to connect to access point now. :mrgreen:

3. Please install rp-pppoe package and configure it now.
You can download this package rp-pppoe-3.8-107.1.i586.rpm from Software.openSUSE.org

#rpm -Uvh rp-pppoe-3.8-107.1.i586.rpm
Preparing... ########################################### [100%]
1:rp-pppoe ########################################### [100%]

#pppoe-setup

Welcome to the Roaring Penguin PPPoE client setup. First, I will run
some checks on your system to make sure the PPPoE client is installed
properly...

Looks good! Now, please enter some information:

USER NAME

>>> Enter your PPPoE user name (default): <--type your username of pppoe account

INTERFACE

>>> Enter the Ethernet interface connected to the DSL modem
For Solaris, this is likely to be something like /dev/hme0.
For Linux, it will be ethn, where 'n' is a number.
(default eth0): <---type wlan0 that is your wireless deivce

MODEM TYPE

We will try to detect if your modem is compliant with RFC 2516
or not. 3COM's 3CP4130 is *NOT* compliant, for instance.

Searching for a modem at interface wlan0...

Not found, trying with 3COM's code...

Didn't find a modem at interface wlan0, you can continue but
things might not work as you expect...
You might want to re-run this script and try a different interface.

Do you want the link to come up on demand, or stay up continuously?
If you want it to come up on demand, enter the idle time in seconds
after which the link should be dropped. If you want the link to
stay up permanently, enter 'no' (two letters, lower-case.)
NOTE: Demand-activated links do not interact well with dynamic IP
addresses. You may have some problems with demand-activated links.
>>> Enter the demand value (default no): <---Enter

Please enter the IP address of your ISP's primary DNS server.
If your ISP claims that 'the server will provide DNS addresses',
enter 'server' (all lower-case) here.
If you just press enter, I will assume you know what you are
doing and not modify your DNS setup.
>>> Enter the DNS information here: <---Enter

PASSWORD

>>> Please enter your PPPoE password: <---type your password of pppoe account
>>> Please re-enter your PPPoE password: <---type your password again

FIREWALLING

Please choose the firewall rules to use. Note that these rules are
very basic. You are strongly encouraged to use a more sophisticated
firewall setup; however, these will provide basic security. If you
are running any servers on your machine, you must choose 'NONE' and
set up firewalling yourself. Otherwise, the firewall rules will deny
access to all standard servers like Web, e-mail, ftp, etc. If you
are using SSH, the rules will block outgoing SSH connections which
allocate a privileged source port.

The firewall choices are:
0 - NONE: This script will not set any firewall rules. You are responsible
for ensuring the security of your machine. You are STRONGLY
recommended to use some kind of firewall rules.
1 - STANDALONE: Appropriate for a basic stand-alone web-surfing workstation
2 - MASQUERADE: Appropriate for a machine acting as an Internet gateway
for a LAN
>>> Choose a type of firewall (0-2): <---type 0

** Summary of what you entered **

Ethernet Interface: wlan0
User name: 71355589@hinet.net
Activate-on-demand: No
DNS: Do not adjust
Firewalling: NONE

>>> Accept these settings and adjust configuration files (y/n)? <---type y

Congratulation! you can start to connect to internet via pppoe-start command now.

# pppoe-start
... Connected!


PS: Here are all of pppoe configuration files.
#cd /etc/ppp/
pppoe.conf
chap-secrets
pap-secrets