Results 1 to 6 of 6

Thread: fail to mount raid5 xfs partition

  1. #1

    Default fail to mount raid5 xfs partition

    I have a raid 5 partition /dev/md0 that is no longer mounted after reboots.

    The file system created on that mount point is xfs.

    I have done the following to debug this but do not understand the root cause. Can anyone help me understand what is the issue and how to fix it (I am not an expert in this stuff).

    This has happened "out of the blue" after a couple of years of trouble free running.

    fsck /dev/md0
    --------------
    fsck 1.40.2 (12-Jul-2007)
    If you wish to check the consistency of an XFS filesystem or
    repair a damaged filesystem, see xfs_check(8) and xfs_repair(8).

    xfs_check /dev/md0
    -------------------
    xfs_check: /dev/md0 is invalid (cannot read first 512 bytes)

    mdadm --detail /dev/md0
    ------------------------
    mdadm: md device /dev/md0 does not appear to be active.

    cat /proc/mdstat
    ----------------
    Personalities :
    md0 : inactive sda5[0](S) sdd5[3](S) sdc5[2](S) sdb5[1](S)
    977522688 blocks

    unused devices: <none>

    Tentative conclusions
    ---------------------
    So it appears that the raid5 is "inactive".
    How can I find out why?
    How can I activate it?

    System Info
    ------------
    uname -a:
    Linux nas 2.6.22.5-31-default #1 SMP 2007/09/21 22:29:00 UTC i686 athlon i386 GNU/Linux

    openSUSE 10.3

    Any help/suggestions *much* appreciated!

  2. #2

    Default Re: fail to mount raid5 xfs partition

    A bit more info...

    /var/log/messages
    -----------------
    There is nothing reported in here that indicates the problem (to me).

    disk failure
    ----------
    I pretty sure thee is not an out and out disk failure because
    sda1 has /boot
    sda2 has /
    sdb2 has /var
    sdc2 has /tmp
    sdd2 has swap
    I can see /tmp, /var and (obviously) /.
    Though no swap is used, "free" indicates it correctly so I assume it is ok.

  3. #3
    Join Date
    Jun 2008
    Location
    Cyberspace
    Posts
    13

    Default Re: fail to mount raid5 xfs partition

    try also looking for some hints through dmesg

    i.e,

    > dmesg | more

    or echo it to a file that you can browse through, or grep through, etc...

    > dmesg > dmesg.txt

    Also, boot-time messages are logged at /var/log/boot.msg (and previous boot at /var/log/boot.omsg)

    good luck!

  4. #4

    Default Re: fail to mount raid5 xfs partition

    Thanks - more info:

    dmesg | more
    -----------
    (relevant excerpt, that don't actually tell me much more than it is probably still a raid problem)...

    md: bind<sdb5>
    md: bind<sdc5>
    md: bind<sdd5>
    md: bind<sda5>
    ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011d80000916254]
    loop: module loaded
    SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
    SGI XFS Quota Management subsystem
    XFS: SB read failed
    ...
    md: could not bd_claim sda5.
    md: could not bd_claim sdb5.
    md: could not bd_claim sdc5.
    md: could not bd_claim sdd5.
    md: autorun ...
    md: ... autorun DONE.

    Any ideas?

    Thanks

  5. #5

    Default Re: fail to mount raid5 xfs partition

    more info that may be relevant...

    mount /mnt/share
    ----------------
    mount: /dev/md0: can't read superblock

  6. #6

    Smile Re: fail to mount raid5 xfs partition

    Solved:
    =======
    Run 'mdadm -E /dev/X' for each raided partition.

    This showed one partition marked as failure.

    I think (since other paritions on this disk are ok) there was a data corruption which was causing the raid to fail in general.

    Then did
    mdadm -A /dev/md0 -f -U summaries /dev/sda5 /dev/sdb5 /dev/sdc5 /dev/sdd5
    which seemed to get it going again, apparently ok.

    After backing up the raid munt, I then rebuilt it by simply adding in the dodgy partition again...

    mdadm /dev/md0 --add /dev/sdb5

    Doing 'cat /proc/mdstat' showed progress and ETA nicely.

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •