OpenSuse 11.0 - qla2xxx

[spetrov_bg]

Hello,

i'm trying to connect OpenSuse 11.0 to my EMC storage system, using qlogic 2342M card and get this errors on /var/log/messages:

1> root# modprobe qla2xxx
--- /var/log/messages ---
qla2xxx 0000:08:05.1: Verifying loaded RISC code...
qla2xxx 0000:08:05.1: Allocated (412 KB) for firmware dump...
scsi10 : qla2xxx
qla2xxx 0000:08:05.1:
QLogic Fibre Channel HBA Driver: 8.02.00-k9
QLogic FCI/O-CARD2Gb/s -
ISP2312: PCI-X (100 MHz) @ 0000:08:05.1 hdma+, host#=10, fw=3.03.20 IPX
qla2xxx 0000:08:05.1: Cable is unplugged...


2> root# fdisk /dev/sdb
Unable to read /dev/sdb
--- /var/log/messages ---
sd 9:0:0:0: [sdb] Device not ready: Sense Key : Not Ready [current]
sd 9:0:0:0: [sdb] Device not ready: Add. Sense: Logical unit not ready, manual intervention required
end_request: I/O error, dev sdb, sector 0
printk: 13 messages suppressed.
Buffer I/O error on device sdb, logical block 0
Buffer I/O error on device sdb, logical block 1
Buffer I/O error on device sdb, logical block 2
Buffer I/O error on device sdb, logical block 3
sd 9:0:0:0: [sdb] Device not ready: Sense Key : Not Ready [current]
sd 9:0:0:0: [sdb] Device not ready: Add. Sense: Logical unit not ready, manual intervention required
end_request: I/O error, dev sdb, sector 0
Buffer I/O error on device sdb, logical block 0
sd 9:0:0:0: [sdb] Device not ready: Sense Key : Not Ready [current]
sd 9:0:0:0: [sdb] Device not ready: Add. Sense: Logical unit not ready, manual intervention required
end_request: I/O error, dev sdb, sector 104857592


any ideas are welcome

[ken_yap]

qla2xxx 0000:08:05.1: Cable is unplugged...

I thought that's pretty clear? Disconnected? Bad fibre?

I have run qla2xxx on 10.1 and 11.1 with an Xserve RAID and the driver is absolutely fine.

[spetrov_bg]

i'm sorry my bad, FC card have 2 ports and i posted wrong/disconnected port information, here is connected port info:

Jul 1 03:26:57 web16 kernel: qla2xxx 0000:08:05.0: Found an ISP2312, irq 32, iobase 0xffffc20003058000
Jul 1 03:26:57 web16 kernel: qla2xxx 0000:08:05.0: Configuring PCI space...
Jul 1 03:26:57 web16 kernel: qla2xxx 0000:08:05.0: Configure NVRAM parameters...
Jul 1 03:26:57 web16 kernel: qla2xxx 0000:08:05.0: Verifying loaded RISC code...
Jul 1 03:26:57 web16 kernel: qla2xxx 0000:08:05.0: Allocated (412 KB) for firmware dump...
Jul 1 03:26:57 web16 kernel: scsi9 : qla2xxx
Jul 1 03:26:57 web16 kernel: qla2xxx 0000:08:05.0: LIP reset occured (f7f7).
Jul 1 03:26:58 web16 kernel: qla2xxx 0000:08:05.0: LIP occured (f7f7).
Jul 1 03:26:58 web16 kernel: qla2xxx 0000:08:05.0: LOOP UP detected (2 Gbps).
Jul 1 03:26:58 web16 kernel: scsi 9:0:0:0: Direct-Access DGC RAID 1 0428 PQ: 0 ANSI: 4
Jul 1 03:26:58 web16 kernel: sd 9:0:0:0: [sdb] 104857600 512-byte hardware sectors (53687 MB)
Jul 1 03:26:58 web16 kernel: sd 9:0:0:0: [sdb] Test WP failed, assume Write Enabled
Jul 1 03:26:58 web16 kernel: sd 9:0:0:0: [sdb] Asking for cache data failed
Jul 1 03:26:58 web16 kernel: sd 9:0:0:0: [sdb] Assuming drive cache: write through
Jul 1 03:26:58 web16 kernel: sd 9:0:0:0: [sdb] 104857600 512-byte hardware sectors (53687 MB)
Jul 1 03:26:58 web16 kernel: sd 9:0:0:0: [sdb] Test WP failed, assume Write Enabled
Jul 1 03:26:58 web16 kernel: sd 9:0:0:0: [sdb] Asking for cache data failed
Jul 1 03:26:58 web16 kernel: sd 9:0:0:0: [sdb] Assuming drive cache: write through
Jul 1 03:26:58 web16 kernel: sdb:<6>sd 9:0:0:0: [sdb] Device not ready: Sense Key : Not Ready [current]
Jul 1 03:26:58 web16 kernel: sd 9:0:0:0: [sdb] Device not ready: Add. Sense: Logical unit not ready, manual intervention required
Jul 1 03:26:58 web16 kernel: end_request: I/O error, dev sdb, sector 0
Jul 1 03:26:58 web16 kernel: printk: 6 messages suppressed.

[ken_yap]

Looks like a bad FC storage unit.

[spetrov_bg]

yes that was storage problem,
after "trespass"-ing LUN on SAN everything works fine.

thank you so mutch