Hp Compaq Nx7010

Hi
My friend has this HP with OpenSUSE 10.3 on it. Everything works wonderfully, but neither of its network cards work properly. The wireless card can detect wireless networks, even connect to them (so it ways) but if I ping another computer on the network it says Destination host unreachable.
As for the Ethernet, the card is displayed in yast, but I plug in a cable and try ping another computer, and the same thing happens... Destination host unreachable.

lspci:

00:00.0 Host bridge: Intel Corporation 82855PM Processor to I/O Controller (rev 03)
00:01.0 PCI bridge: Intel Corporation 82855PM Processor to AGP Controller (rev 03)
00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 01)
00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 01)
00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 01)
00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 81)
00:1f.0 ISA bridge: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge (rev 01)
00:1f.1 IDE interface: Intel Corporation 82801DBM (ICH4-M) IDE Controller (rev 01)
00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 01)
00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 01)
00:1f.6 Modem: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem Controller (rev 01)
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon RV250 [Mobility FireGL 9000] (rev 01)
02:00.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 80)
02:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 20)
02:02.0 Network controller: Intel Corporation PRO/Wireless LAN 2100 3B Mini PCI Adapter (rev 04)
02:04.0 CardBus bridge: ENE Technology Inc CB1410 Cardbus Controller (rev 01)

ifconfig:

eth1******Link encap:Ethernet**HWaddr 00:02:3F:6B:BA:96
**********inet addr:192.168.0.205**Bcast:192.168.0.255**Mask:255.255.255.0
**********UP BROADCAST MULTICAST**MTU:1500**Metric:1
**********RX packets:0 errors:0 dropped:0 overruns:0 frame:0
**********TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
**********collisions:0 txqueuelen:1000
**********RX bytes:0 (0.0 b)**TX bytes:0 (0.0 b)
**********Interrupt:10 Base address:0xc000

lo********Link encap:Local Loopback
**********inet addr:127.0.0.1**Mask:255.0.0.0
**********UP LOOPBACK RUNNING**MTU:16436**Metric:1
**********RX packets:88 errors:0 dropped:0 overruns:0 frame:0
**********TX packets:88 errors:0 dropped:0 overruns:0 carrier:0
**********collisions:0 txqueuelen:0
**********RX bytes:5960 (5.8 Kb)**TX bytes:5960 (5.8 Kb)

few things to check:-

1 ) firewall isn't blocking
2 ) ipv6 disabled
3 ) dns & host names is correct

Thanx for replying!

1) I'm very sure firewall isn't blocking. I turned firewall off and it still wouldn't ping.
2) ipv6 is disabled. I habitually turn in off during installation every time I install suse.
3) DNS is correct. But I'm not sure what the correct hostname should be?

Everything points to it working. KInternet says I'm connected to the wireless network. I'm sure I put the WEP passkey in correctly. I double-checked everythng.

Ethernet is even less hopeful, strangely... I plugged it into the router using a working cable (I tested it), but in yast it says "not connected" for the Ethernet...

It says it's a Compaq RTL-8139C+, does that mean Realtek drivers won't work with it?

Nevermind, I got it working. Turns out I got the password wrong!!! Ha Ha!!!!

Good for you, glad you got it working.now enjoy