Connection

hi

SuSE Meta pppd (smpppd-ifcfg), Version 1.59 on linux-6g1g.
Status is: disconnected
trying to connect to smpppd
connect to smpppd
Status is: disconnected
Status is: connecting
pppd[0]: Plugin passwordfd.so loaded.
pppd[0]: --> WvDial: Internet dialer version 1.56 (abuild@mandelbrot)
pppd[0]: --> Initializing modem.
pppd[0]: --> Sending: ATZ
pppd[0]: ATZ
pppd[0]: OK
pppd[0]: --> Sending: AT Q0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
pppd[0]: AT Q0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
pppd[0]: OK
pppd[0]: --> Sending: ATM0
pppd[0]: ATM0
pppd[0]: OK
pppd[0]: --> Modem initialized.
pppd[0]: --> Sending: ATDT9718585
pppd[0]: --> Waiting for carrier.
pppd[0]: ATDT9718585
pppd[0]: NO CARRIER
pppd[0]: --> No Carrier! Trying again.
pppd[0]: --> Sending: ATDT9718585
pppd[0]: --> Waiting for carrier.
pppd[0]: ATDT9718585
pppd[0]: --> Timed out while dialing. Trying again.
pppd[0]: --> Sending: ATDT9718585
pppd[0]: --> Waiting for carrier.
pppd[0]: ATDT9718585
pppd[0]: CONNECT 46667
pppd[0]: --> Carrier detected. Waiting for prompt.
pppd[0]: User Access Verification
pppd[0]: Username:
pppd[0]: --> Looks like a login prompt.
pppd[0]: --> Sending: abdolahnoori
pppd[0]: abdolahnoori
pppd[0]: Password:
pppd[0]: --> Looks like a password prompt.
pppd[0]: --> Sending: (password)
pppd[0]: % Authentication failed.
pppd[0]: Username:
pppd[0]: --> Looks like a login prompt.
pppd[0]: --> Sending: abdolahnoori
pppd[0]: --> Don't know what to do! Starting pppd and hoping for the best.
pppd[0]: Serial connection established.
pppd[0]: Renamed interface ppp0 to modem0
pppd[0]: Using interface modem0
Status is: connecting
pppd[0]: Connect: modem0 <--> /dev/ttyS0
pppd[0]: Hangup (SIGHUP)
pppd[0]: Modem hangup
pppd[0]: Connection terminated.
Status is: disconnected
pppd[0] died: A modem hung up the phone (exit code 16)

how to solve my problem?

help me what i do to connect to internet

i use external modem and work with opensuse 10.3 and kinternet for connection

Its been a while since I used a dial up modem but I believe there is a setup in YaST>Network Devices> Modem that allows you to use "stupid mode" for some ISP's that are using dated equipment.

Have you successfully logged in to this ISP with any other computer? It looks like an authentication problem. Maybe you are supposed to send username@something instead of username?

but i log in to isp in windows without any problem

i can't find stupid mode in setup network device

may i configure it in terminal?

They seemed to rename it to Ignore Prompts.

hope that helps. Also check to see if your username and password are correct for any capitalization or syntax errors.

i configure my network device as your image but i can't connect

could you help me about connecting as same sa vpn in windows

i have a local vpn in my office and i connect through it

i make a vpn connection then connect to internet in windows

how do i do that in suse?

thank you

I am not versed in Virtual Private Networks. Do you have a ethernet card that hooks to a switch or router? If so and you can get an IP assigned either via DHCP or stable you can use the Network Devices> Network card to set up your box.

I would also suggest posting a separate question concerning how to connect through a VPN so someone with VPN background might see the Thread.

Back to the modem. Perhaps you should give the model of it and type of ISP that you are trying to connect with. Is the Firewall configured properly? And could you post the last connection attempt log after selecting Ignore Prompts in the Setup section?

SuSE Meta pppd (smpppd-ifcfg), Version 1.59 on linux-6g1g.
Status is: disconnected
trying to connect to smpppd
connect to smpppd
Status is: disconnected
Status is: connecting
pppd[0]: Plugin passwordfd.so loaded.
pppd[0]: --> WvDial: Internet dialer version 1.56 (abuild@mandelbrot)
pppd[0]: --> Initializing modem.
pppd[0]: --> Sending: ATZ
pppd[0]: ATZ
pppd[0]: OK
pppd[0]: --> Sending: AT Q0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
pppd[0]: AT Q0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
pppd[0]: OK
pppd[0]: --> Sending: ATM1
pppd[0]: ATM1
pppd[0]: OK
pppd[0]: --> Modem initialized.
pppd[0]: --> Sending: ATDT9718000
pppd[0]: --> Waiting for carrier.
pppd[0]: ATDT9718000
pppd[0]: CONNECT 45333
pppd[0]: User Access Verification
pppd[0]: Username:
pppd[0]: --> Carrier detected. Chatmode finished.
pppd[0]: Serial connection established.
pppd[0]: Renamed interface ppp0 to modem0
pppd[0]: Using interface modem0
Status is: connecting
pppd[0]: Connect: modem0 <--> /dev/ttyS0
pppd[0]: PAP authentication succeeded
pppd[0]: replacing old default route to eth1 [10.5.4.1]
pppd[0]: local IP address 217.219.68.228
pppd[0]: remote IP address 217.219.69.3
pppd[0]: primary DNS address 217.218.155.104
pppd[0]: secondary DNS address 217.218.155.105
pppd[0]: Script /etc/ppp/ip-up finished (pid 5449), status = 0x0
Status is: connected
i don't any configuration on firewall
it's the log after checked ignore prompt

Status is: connected
i don't any configuration on firewall
it's the log after checked ignore prompt
[/b]

Ok color me confused, your log shows Status as being connected. Perhaps IPv6 needs to be disabled, do this in YaST>System>Sysconfig editor>Desktop>KDE_use_IPV6 set to no.

hi
thanks for guiding me

i connected successfuly

first i create a new connection

then i checked the ignore prompt and external firwall

then s you said,i disablu ipv6

at least i connected

do youknow how to enable 3d desktop?