Suse 10.0 2.6.13-15.8 Asus P4C800-E SATA/PATA problem

Hi All,

I've three disk's connected to my Asus-Board:
SATA: sda, sdb
PATA: sdc

all worked fine with Suse 9.3
After an update from 9.3 to 10.0 the system doesn't found
my disk sdc (PATA). Nothing was changed in BIOS-setup since 9.3

Bootup told me the following about my disk's.

<7>libata version 1.12 loaded.
<7>ata_piix version 1.04
<6>ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 169
<7>PCI: Setting latency timer of device 0000:00:1f.2 to 64
<6>ata1: SATA max UDMA/133 cmd 0xEFE0 ctl 0xEFAE bmdma 0xEF90 irq 169
<6>ata2: SATA max UDMA/133 cmd 0xEFA0 ctl 0xEFAA bmdma 0xEF98 irq 169
<7>ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003
88:207f
<6>ata1: dev 0 ATA, max UDMA/133, 312581808 sectors: lba48
<6>ata1: dev 0 configured for UDMA/133
<6>scsi0 : ata_piix
<7>ata2: dev 0 cfg 49:2f00 82:346b 83:7f61 84:4003 85:3469 86:3c41 87:4003
88:207f
<6>ata2: dev 0 ATA, max UDMA/133, 312581808 sectors: lba48
<6>ata2: dev 0 configured for UDMA/133
<6>scsi1 : ata_piix
<5> Vendor: ATA Model: ST3160023AS Rev: 3.05
<5> Type: Direct-Access ANSI SCSI revision: 05
<5>SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
<5>SCSI device sda: drive cache: write back
<5>SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
<5>SCSI device sda: drive cache: write back
<6> sda: sda1 sda2 < sda5 > sda3 sda4
<5>Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
<5> Vendor: ATA Model: WDC WD1600JD-00H Rev: 08.0
<5> Type: Direct-Access ANSI SCSI revision: 05
<5>SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB)
<5>SCSI device sdb: drive cache: write back
<5>SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB)
<5>SCSI device sdb: drive cache: write back
<6> sdb: sdb1 sdb2 <<5>Attached scsi generic sg0 at scsi0, channel 0, id 0,
lun 0, type 0
<4> sdb5 sdb6 sdb7 >
<5>Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
<5>Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 0
<7>sata_promise version 1.02
<6>ACPI: PCI Interrupt 0000:03:04.0[A] -> GSI 23 (level, low) -> IRQ 177
<6>ata3: SATA max UDMA/133 cmd 0xF881A200 ctl 0xF881A238 bmdma 0x0 irq 177
<6>ata4: SATA max UDMA/133 cmd 0xF881A280 ctl 0xF881A2B8 bmdma 0x0 irq 177
<6>ata3: no device found (phy stat 00000000)
<6>scsi2 : sata_promise
<6>ata4: no device found (phy stat 00000000)
<6>scsi3 : sata_promise

tecra68@yahoo.de adjusted his/her tinfoil beanie to post:

> Hi All,
>
> I've three disk's connected to my Asus-Board:
> SATA: sda, sdb

> PATA: sdc

PATA as a scsi disk?

Is this a hard drive or a cd/dvd rom?

HTH
--
Mark
Twixt hill and high water
N. Wales, UK
Novell Support Forums SysOp

> tecra68@yahoo.de adjusted his/her tinfoil beanie to post:
>
> > Hi All,
> >
> > I've three disk's connected to my Asus-Board:
> > SATA: sda, sdb
>
> > PATA: sdc
>
> PATA as a scsi disk?
>
> Is this a hard drive or a cd/dvd rom?
>
> HTH
> --
> Mark
> Twixt hill and high water
> N. Wales, UK
> Novell Support Forums SysOp
>


Yes,
this Harddisk (SAMSUNG SP2514N) is connected to the onboard Promise
PDC20378 RAID Ultra ATA 133 connector and was in use as /dev/sdc (Suse 9.3).
Here, I've booted my system with Suse 9.3 and show you the
boot.msg from IDE section to the end of SCSI section:

<6>ICH5: IDE controller at PCI slot 0000:00:1f.1
<4>PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
<6>ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 5 (level, low) -> IRQ 5
<6>ICH5: chipset revision 2
<6>ICH5: not 100% native mode: will probe irqs later
<6> ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hdaMA, hdbio
<6> ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdcMA, hddio
<7>Probing IDE interface ide0...
<4>hda: PLEXTOR DVDR PX-708A, ATAPI CD/DVD-ROM drive
<4>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
<6>hda: ATAPI 94X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
<6>Uniform CD-ROM driver Revision: 3.20
<7>Probing IDE interface ide1...
<4>hdc: RICOH DVD/CDRW MP9200, ATAPI CD/DVD-ROM drive
<4>ide1 at 0x170-0x177,0x376 on irq 15
<6>hdc: ATAPI 40X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
<7>libata version 1.10 loaded.
<7>ata_piix version 1.03
<6>ACPI: PCI interrupt 0000:00:1f.2[A] -> GSI 5 (level, low) -> IRQ 5
<7>PCI: Setting latency timer of device 0000:00:1f.2 to 64
<6>ata1: SATA max UDMA/133 cmd 0xEFE0 ctl 0xEFAE bmdma 0xEF90 irq 5
<6>ata2: SATA max UDMA/133 cmd 0xEFA0 ctl 0xEFAA bmdma 0xEF98 irq 5
<7>ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003
88:207f
<6>ata1: dev 0 ATA-6, max UDMA/133, 312581808 sectors: LBA48
<6>ata1: dev 0 configured for UDMA/133
<6>scsi0 : ata_piix
<7>ata2: dev 0 cfg 49:2f00 82:346b 83:7f61 84:4003 85:3469 86:3c41 87:4003
88:207f
<6>ata2: dev 0 ATA-6, max UDMA/133, 312581808 sectors: LBA48
<6>ata2: dev 0 configured for UDMA/133
<6>scsi1 : ata_piix
<5> Vendor: ATA Model: ST3160023AS Rev: 3.05
<5> Type: Direct-Access ANSI SCSI revision: 05
<5>SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
<5>SCSI device sda: drive cache: write back
<5>SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
<5>SCSI device sda: drive cache: write back
<6> sda: sda1 sda2 < sda5 > sda3 sda4
<5>Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
<5>Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
<5> Vendor: ATA Model: WDC WD1600JD-00H Rev: 08.0
<5> Type: Direct-Access ANSI SCSI revision: 05
<5>SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB)
<5>SCSI device sdb: drive cache: write back
<5>SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB)
<5>SCSI device sdb: drive cache: write back
<6> sdb: sdb1 sdb2 < sdb5 sdb6 sdb7 >
<5>Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
<5>Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 0
<7>sata_promise version 1.01
<6>ACPI: PCI interrupt 0000:03:04.0[A] -> GSI 10 (level, low) -> IRQ 10
<6>sata_promise PATA port found
<6>ata3: SATA max UDMA/133 cmd 0xF8C94200 ctl 0xF8C94238 bmdma 0x0 irq 10
<6>ata4: SATA max UDMA/133 cmd 0xF8C94280 ctl 0xF8C942B8 bmdma 0x0 irq 10
<6>ata5: PATA max UDMA/133 cmd 0xF8C94300 ctl 0xF8C94338 bmdma 0x0 irq 10
<6>ata3: no device found (phy stat 00000000)
<6>scsi2 : sata_promise
<6>ata4: no device found (phy stat 00000000)
<6>scsi3 : sata_promise
<7>ata5: dev 0 cfg 49:2f00 82:746b 83:7f61 84:4023 85:7469 86:3c01 87:4023
88:203f
<6>ata5: dev 0 ATA-7, max UDMA/100, 488397168 sectors: LBA48
<6>ata5: dev 0 configured for UDMA/100
<6>scsi4 : sata_promise
<5> Vendor: ATA Model: SAMSUNG SP2514N Rev: VF10
<5> Type: Direct-Access ANSI SCSI revision: 05
<5>SCSI device sdc: 488397168 512-byte hdwr sectors (250059 MB)
<5>SCSI device sdc: drive cache: write back
<5>SCSI device sdc: 488397168 512-byte hdwr sectors (250059 MB)
<5>SCSI device sdc: drive cache: write back
<6> sdc: sdc1 sdc2 sdc3 sdc4
<5>Attached scsi disk sdc at scsi4, channel 0, id 0, lun 0
<5>Attached scsi generic sg2 at scsi4, channel 0, id 0, lun 0, type 0

Eddy