Okay I was asked to make sure ipv6 was disabled and provide the following information
/sbin/ifconfig -a
/sbin/route -n
cat /etc/resolv.conf
So ipv6 was disabled, it's one of the first things I check with networking on any o/s tbh.
Here's the ouptut requested, plus lsmod output, ethtool output and an extract of perhaps relevant entries in my dmesg
ifconfig output
===============
eth1 Link encap:Ethernet HWaddr 00:1F
0:20:8E:04
inet addr:192.168.0.5 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1492 Metric:1
RX packets:25 errors:0 dropped:0 overruns:0 frame:0
TX packets:49 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1690 (1.6 Kb) TX bytes:5771 (5.6 Kb)
Interrupt:249 Base address:0x2000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:6 errors:0 dropped:0 overruns:0 frame:0
TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:300 (300.0 b) TX bytes:300 (300.0 b)
resolv.conf output
==================
### /etc/resolv.conf file autogenerated by netconfig!
#
# Before you change this file manually, consider to define the
# static DNS configuration using the following variables in the
# /etc/sysconfig/network/config file:
# NETCONFIG_DNS_STATIC_SEARCHLIST
# NETCONFIG_DNS_STATIC_SERVERS
# NETCONFIG_DNS_FORWARDER
# or disable DNS configuration updates via netconfig by setting:
# NETCONFIG_DNS_POLICY=''
#
# See also the netconfig(8) manual page and other documentation.
#
# Note: Manual change of this file disables netconfig too, but
# may get lost when this file contains comments or empty lines
# only, the netconfig settings are same with settings in this
# file and in case of a "netconfig update -f" call.
#
nameserver 192.168.4.100
nameserver 192.168.8.100
netstat -anr output
===================
Kernel IP routing table
Destination Gateway Genmask Flags MSS Window irtt Iface
192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1
169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1
127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo
0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth1
lsmod output
============
Module Size Used by
sco 12572 2
rfcomm 42648 0
bridge 57288 1
stp 3020 1 bridge
bnep 14664 2
l2cap 24056 6 rfcomm,bnep
bluetooth 63652 6 sco,rfcomm,bnep,l2cap
nls_utf8 2160 1
snd_pcm_oss 48896 0
snd_mixer_oss 16808 1 snd_pcm_oss
snd_seq 61968 0
microcode 25912 0
fuse 61088 5
loop 17924 0
dm_mod 73952 0
snd_hda_intel 545508 0
snd_usb_audio 97936 1
snd_usb_lib 18856 1 snd_usb_audio
snd_pcm 95440 3 snd_pcm_oss,snd_hda_intel,snd_usb_audio
uvcvideo 56240 0
snd_timer 26664 2 snd_seq,snd_pcm
snd_rawmidi 26768 1 snd_usb_lib
snd_seq_device 8604 2 snd_seq,snd_rawmidi
snd_page_alloc 9816 2 snd_hda_intel,snd_pcm
jmicron 3048 0
compat_ioctl32 8536 1 uvcvideo
snd_hwdep 9072 2 snd_hda_intel,snd_usb_audio
snd 74632 13 snd_pcm_oss,snd_mixer_oss,snd_seq,snd_hda_intel,sn d_usb_audio,snd_usb_lib,snd_pcm,snd_timer,snd_rawm idi,snd_seq_device,snd_hwdep
iTCO_wdt 13040 0
r8169 31388 0
videodev 35328 2 uvcvideo,compat_ioctl32
sr_mod 16196 1
ohci1394 31380 0
i2c_i801 12836 0
iTCO_vendor_support 4268 1 iTCO_wdt
rtc_cmos 13960 0
mii 6024 1 r8169
v4l1_compat 14220 2 uvcvideo,videodev
cdrom 36200 1 sr_mod
ahci 34628 0
ieee1394 98880 1 ohci1394
i2c_core 35280 1 i2c_i801
pata_jmicron 4104 0
pcspkr 3064 0
joydev 12112 0
soundcore 8816 1 snd
rtc_core 22420 1 rtc_cmos
serio_raw 6412 0
button 8328 0
rtc_lib 3560 1 rtc_core
sg 35344 0
usbhid 52896 0
hid 41568 1 usbhid
ff_memless 8912 1 usbhid
sd_mod 35064 7
uhci_hcd 27928 0
ehci_hcd 55348 0
crc_t10dif 2152 1 sd_mod
usbcore 198656 7 snd_usb_audio,snd_usb_lib,uvcvideo,usbhid,uhci_hcd ,ehci_hcd
pata_via 9836 0
sata_via 11772 0
edd 10272 0
ext3 141912 3
mbcache 10412 1 ext3
jbd 68824 1 ext3
fan 6016 0
ide_pci_generic 4652 0
ide_core 118012 2 jmicron,ide_pci_generic
ata_generic 6044 0
ata_piix 21628 6
libata 183376 6 ahci,pata_jmicron,pata_via,sata_via,ata_generic,at a_piix
scsi_mod 179144 4 sr_mod,sg,sd_mod,libata
dock 14564 1 libata
thermal 24232 0
processor 49904 1 thermal
thermal_sys 14336 3 fan,thermal,processor
hwmon 4040 1 thermal_sys
ethtool output
==============
Settings for eth1:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Advertised auto-negotiation: Yes
Speed: 100Mb/s
Duplex: Full
Port: MII
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: pumbg
Wake-on: g
Current message level: 0x00000033 (51)
Link detected: yes
dmesg extract
=============
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 2.6.27.7-9-default (geeko@buildhost) (gcc version 4.3.2 [gcc-4_3-branch revision 141291] (SUSE Linux) ) #1 SMP 2008-12-04 18:10:04 +0100
Command line: root=/dev/disk/by-id/ata-ST3360320AS_6QF2WZ04-part3 resume=/dev/disk/by-id/ata-ST3360320AS_6QF2WZ04-part2 splash=silent vga=0x31a
<snip>
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 524288 bind 65536)
TCP reno registered
NET: Registered protocol family 1
<snip>
r8169: eth1: link up
r8169: eth1: link up
So far, no matter what I have tried does not work and ofc all other computers on the network are fine, lol