Hello all,
I wonder if somebody can point me into right direction with WLAN setup on SuSE 11.1.
My wireless hardware config on Toshiba Satellite M60 (print from YaST hardware config):
Code:
16: PCI 602.0: 0282 WLAN controller
[Created at pci.310]
UDI: /org/freedesktop/Hal/devices/pci_8086_4220
Unique ID: JNkJ.BHy7RZPPHRF
Parent ID: 6NW+.InKz0bgid89
SysFS ID: /devices/pci0000:00/0000:00:1e.0/0000:06:02.0
SysFS BusID: 0000:06:02.0
Hardware Class: network
Model: "Intel PRO/Wireless 2200BG Network Connection"
Vendor: pci 0x8086 "Intel Corporation"
Device: pci 0x4220 "PRO/Wireless 2200BG Network Connection"
SubVendor: pci 0x8086 "Intel Corporation"
SubDevice: pci 0x2741
Revision: 0x05
Driver: "ipw2200"
Driver Modules: "ipw2200"
Device File: eth1
Features: WLAN
Memory Range: 0xc4005000-0xc4005fff (rw,non-prefetchable)
IRQ: 22 (439663 events)
HW Address: 00:12:f0:c0:13:3f
Link detected: no
WLAN channels: 1 2 3 4 5 6 7 8 9 10 11
WLAN frequencies: 2.412 2.417 2.422 2.427 2.432 2.437 2.442 2.447 2.452 2.457 2.462
WLAN bitrates: 1 2 5.5 11 6 9 12 18 24 36 48 54
WLAN encryption modes: WEP40 WEP104 TKIP CCMP
WLAN authentication modes: open sharedkey wpa-psk wpa-eap
Requires: ipw-firmware
Module Alias: "pci:v00008086d00004220sv00008086sd00002741bc02sc80i00"
Driver Info #0:
Driver Status: ipw2200 is active
Driver Activation Cmd: "modprobe ipw2200"
Config Status: cfg=no, avail=yes, need=no, active=unknown
Attached to: #25 (PCI bridge)
...
46: udi = '/org/freedesktop/Hal/devices/net_00_12_f0_c0_13_3f'
info.subsystem = 'net'
info.product = 'WLAN Interface'
info.udi = '/org/freedesktop/Hal/devices/net_00_12_f0_c0_13_3f'
info.capabilities = { 'net', 'net.80211' }
net.80211.mac_address = 81348531007ull (0x12f0c0133full)
info.category = 'net.80211'
net.originating_device = '/org/freedesktop/Hal/devices/pci_8086_4220'
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1e.0/0000:06:02.0/net/eth1'
net.interface = 'eth1'
info.parent = '/org/freedesktop/Hal/devices/pci_8086_4220'
net.address = '00:12:f0:c0:13:3f'
net.linux.ifindex = 3 (0x3)
net.arp_proto_hw_id = 1 (0x1)
linux.hotplug_type = 2 (0x2)
linux.subsystem = 'net'
...
71: None 01.0: 10701 Ethernet
[Created at net.124]
Unique ID: L2Ua.ndpeucax6V1
Parent ID: JNkJ.BHy7RZPPHRF
SysFS ID: /class/net/eth1
SysFS Device Link: /devices/pci0000:00/0000:00:1e.0/0000:06:02.0
Hardware Class: network interface
Model: "Ethernet network interface"
Driver: "ipw2200"
Driver Modules: "ipw2200"
Device File: eth1
HW Address: 00:12:f0:c0:13:3f
Link detected: no
Config Status: cfg=no, avail=yes, need=no, active=unknown
Attached to: #16 (WLAN controller)
...
97: udi = '/org/freedesktop/Hal/devices/pci_8086_4220'
pci.subsys_vendor_id = 32902 (0x8086)
info.subsystem = 'pci'
pci.device_class = 2 (0x2)
info.product = 'PRO/Wireless 2200BG Network Connection'
pci.device_subclass = 128 (0x80)
info.udi = '/org/freedesktop/Hal/devices/pci_8086_4220'
pci.device_protocol = 0 (0x0)
pci.vendor = 'Intel Corporation'
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1e.0/0000:06:02.0'
info.vendor = 'Intel Corporation'
info.parent = '/org/freedesktop/Hal/devices/pci_8086_2448'
pci.product = 'PRO/Wireless 2200BG Network Connection'
pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1e.0/0000:06:02.0'
pci.subsys_vendor = 'Intel Corporation'
pci.product_id = 16928 (0x4220)
linux.hotplug_type = 2 (0x2)
pci.vendor_id = 32902 (0x8086)
linux.subsystem = 'pci'
info.linux.driver = 'ipw2200'
pci.subsys_product_id = 10049 (0x2741)
...
>> int.7: hdb
>> int.7.1: modules
>> int.8: usbscsi
>> int.9: hotplug
>> int.10: modem
>> int.11: wlan
>> int.12: udev
iwconfig brings following results:
Code:
linux-gvn1:/home/root # iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
eth1 unassociated ESSID:off/any
Mode:Managed Channel=0 Access Point: Not-Associated
Bit Rate:0 kb/s Tx-Power=20 dBm Sensitivity=8/0
Retry limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:24 Missed beacon:0
Many thanks for any hints,
Marin